SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSUBARU2022IMPREZA BASE, 4D SEDAN, AUTOMATIC CVT TRANSREPAIR AND DIAGNOSISRESTRAINTSAIR BAG, SRSAIRBAG SYSTEMAIRBAG MODULE DISPOSAL (DEPLOYMENT PROCESSING ON VEHICLE)PROCEDURESIDE AIRBAG MODULE
2022 Subaru Impreza Base, 4D Sedan, Automatic CVT Trans

Side Airbag Module

2022 Subaru Impreza Base, 4D Sedan, Automatic CVT TransSECTION Side Airbag Module
  1. Turn the ignition switch to OFF.
  2. Disconnect the ground terminal from the battery sensor, and wait for at least 60 seconds before starting work. Ref. to REPAIR CONTENTS>REPAIR CONTENTS>NOTE>BATTERY .
    NOTE:

    For the hybrid model, disconnect the battery negative terminal. 

  3. Disconnect the side airbag module connector under the front seat cushion. Ref. to AIRBAG SYSTEM>AIRBAG CONNECTOR>PROCEDURE>SIDE AIRBAG MODULE .
  4. Adjust both the front seat and front seat backrest to the center positions.
  5. Short the terminal to the alligator clip furnished as AIRBAG DEPLOYMENT TOOL.
    CAUTION:

    The AIRBAG DEPLOYMENT TOOL should be kept shorted on the terminals until just before activation of airbag module. 

    Preparation tool: 

    ST: AIRBAG DEPLOYMENT TOOL (98299PA030)

  6. Connect the AIRBAG DEPLOYMENT TOOL (A) and test harness adapter AR (B).

    Preparation tool: 

    ST: TEST HARNESS ADAPTER AR (98299CA000)

    G10270509Courtesy of SUBARU OF AMERICA, INC.
  7. Connect the test harness adapter AR to the side airbag module connector (yellow).
    CAUTION:

    Do not place any object on front seat. 

  8. Make sure there is no one inside the vehicle.
  9. Extend the wiring of AIRBAG DEPLOYMENT TOOL to the limit, and close all the windows and sunroof completely.
    G10270499Courtesy of SUBARU OF AMERICA, INC.
  10. Move the battery at least 5 m (16 ft) from the vehicle, and confirm safety in the area.
  11. Connect the AIRBAG DEPLOYMENT TOOL alligator clip to the battery negative (-) terminal.
  12. Connect the other cable of AIRBAG DEPLOYMENT TOOL to the battery positive (+) terminal, and activate the airbag module.
    CAUTION:
    • After activation, the airbag module will be extremely hot. Let it cool down for at least 40 minutes in an area with no one around. 
    • Do not expose the activated airbag module to water. 
    G10270500Courtesy of SUBARU OF AMERICA, INC.
  13. Remove the side airbag module. Ref. to AIRBAG SYSTEM>SIDE AIRBAG MODULE>REMOVAL .
  14. Place the activated airbag module in a sealed vinyl bag, then discard.
    G10270517Courtesy of SUBARU OF AMERICA, INC.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.