Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
DTC U0594: Invalid Data Received From Hybrid Powertrain Control Module
DTC detecting condition:
Defective data from Hybrid vehicle control ECU assembly.
Trouble symptom:
Hybrid fail lamp illuminates.
Before performing diagnosis, refer to "CAUTION" in "General Description". Ref. to LAN SYSTEM (DIAGNOSTICS) (HEV)>GENERAL DESCRIPTION>CAUTION .
- CHECK CAN COMMUNICATION HARNESS
.
Perform the basic diagnostic procedure to check for fault in CAN communication harness. Ref. to LAN SYSTEM (DIAGNOSTICS) (HEV)>BASIC DIAGNOSTIC PROCEDURE .
Was the basic diagnostic procedure performed up to step 7?
Yes: Go to 2.
No: Perform the basic diagnostic procedure. Ref. to LAN SYSTEM (DIAGNOSTICS) (HEV)>BASIC DIAGNOSTIC PROCEDURE .
- CHECK DTC (OTHER THAN U-CODE)
.
Check the displayed DTC.
Is DTC other than U*** displayed? (Current malfunction)
Yes: Perform the diagnosis for the displayed DTCs other than U-code.
No: Go to 3.
- CHECK DTC (U-CODE)
.
Check the displayed DTC.
Is DTC for the bus off or the data no-receive displayed? (Current malfunction)
Yes: Perform the diagnosis for DTCs for the displayed bus off or the data no-receive.
No: Go to 4.
- CHECK DTC
.
Check the displayed DTC.
Is DTC U0594 displayed? (Current malfunction)
Yes: Go to 5.
No: Go to 7.
- CHECK DTC
.
- Turn the ignition switch to OFF.
- Disconnect the Hybrid vehicle control ECU assembly connector.
- Connect the disconnected connectors.
- Turn the ignition switch to ON.
- Using the Subaru Select Monitor, read all DTCs. Ref. to LAN SYSTEM (DIAGNOSTICS) (HEV)>DIAGNOSTIC TROUBLE CODE (DTC) .
Is DTC U0594 displayed? (Current malfunction)
Yes: Go to 6.
No: Go to 7.
- CHECK DTC
.
Using the Subaru Select Monitor, read all DTCs. Ref. to LAN SYSTEM (DIAGNOSTICS) (HEV)>DIAGNOSTIC TROUBLE CODE (DTC) .
Is DTC U0594 detected in several modules? (Current malfunction)
Yes: Replace Hybrid vehicle control ECU assembly. Ref. to HYBRID ELECTRIC VEHICLE>HYBRID POWERTRAIN CONTROL MODULE .
No: Replace the module that the DTC has been detected.
- CHECK HARNESS
.
- Shake the harness, and check for poor contact.
- Using the Subaru Select Monitor, read all DTCs. Ref. to LAN SYSTEM (DIAGNOSTICS) (HEV)>DIAGNOSTIC TROUBLE CODE (DTC) .
Is DTC U0594 displayed? (Current malfunction)
Yes: Repair the poor contact of harness, or replace the harness.
No: Go to 8.
- CHECK CONNECTOR
.
Check the connector used for high speed CAN for poor contact.
Is there poor contact of connector?
Yes: Repair the connector that has poor contact, or replace harness.
No: It is possible that temporary poor communication occurs. Delete the DTC.
NO RELATED
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.