SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSUBARU2016LEGACY 2.5IREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT VARIANT/TRIMSECTION 7 (CONTINUOUSLY VARIABLE TRANSAXLE (CVT) (H6DO))GENERAL DESCRIPTIONPREPARATION TOOLSPECIAL TOOL
2016 Subaru Legacy 2.5i

Special Tool

2016 Subaru Legacy 2.5iSECTION Special Tool
WARNING: This page is about a different variant/trim than selected.
ILLUSTRATION TOOL NUMBER DESCRIPTION REMARKS
  41099AJ010 SPECIAL TOOL H6
  • Used for removing and installing transmission.
  • For H6 engine.
  18360AA020 HANGER
  • Used for removing and installing transmission.
  • For H6 engine.
  18801AA000 OIL PRESSURE GAUGE ASSY Used for measuring the secondary pressure (line pressure).
  18658AA020 WRENCH COMPL RETAINER Used for removing and installing the differential side retainer.
  18681AA000 PRESSURE GAUGE ADAPTER Used for measuring the secondary pressure (line pressure) and transfer clutch hydraulic pressure.
NOTE: Used together with the genuine O-ring (part No. 806911080).
  18769AA000 EXPANDER PULLEY Used for removing and installing the secondary pulley assembly.
  99099AJ000 ENGINE HANGER
  • Used for removing and installing the automatic transmission assembly.
  • Used together with CHAIN BALANCER (99099AJ010).
  99099AJ010 CHAIN BALANCER
  • Used for removing and installing the automatic transmission assembly.
  • Used together with ENGINE HANGER (99099AJ000).
  498897700 OIL PRESSURE ADAPTER SET Used for measuring the secondary pressure (line pressure) hydraulic pressure.
  34099AC020 ADAPTER HOSE B Used for measuring the transfer clutch hydraulic pressure.
NOTE: Used with genuine union screw (Part No. 801914010) and gasket (Part No. 803914060).
  34099AC010 ADAPTER HOSE A Used for measuring the transfer clutch hydraulic pressure.
  73099SG000 SPECIAL TOOL CONDENSER Used for installing the transfer clutch pressure test plug.
  18270AA040 SOCKET Used for installing the transfer clutch pressure test plug.
  498575400 OIL PRESSURE GAUGE ASSY Used for measuring the transfer clutch hydraulic pressure.
  498277200 STOPPER SET
  • Used for removing and installing automatic transmission assembly to engine.
  • Used for preventing the torque converter from dropping off.
  398527700 PULLER ASSY
  • Used for removing the extension case oil seal.
  • Used for removing the roller bearing of the primary pulley and secondary pulley.
  • Used for removing the bearing of reduction driven gear.
  • Used for removing the differential side retainer bearing outer race.
  18760AA000 CLAW
  • Used for removing ball bearing of front reduction driven gear.
  • Used together with PULLER ASSY (398527700).
  498057300 INSTALLER Used for installing the extension case oil seal.
  18632AA000 TRANSMISSION STAND Used for disassembling and assembling the transmission.
  498255400 PLATE Used for measuring the backlash of hypoid gear.
  498247001 MAGNET BASE
  • Used for measuring the backlash of differential bevel pinion gear.
  • Used for measuring the backlash of hypoid gear.
  • Used for measuring the clearance in forward clutch.
  • Used together with DIAL GAUGE (498247100).
  498247100 DIAL GAUGE
  • Used for measuring the backlash of differential bevel pinion gear.
  • Used for measuring the backlash of hypoid gear.
  • Used for measuring the clearance in forward clutch.
  • Used together with DIAL GAUGE (498247101).
  18675AA000 DIFFERENTIAL SIDE OIL SEAL INSTALLER Used for installing the differential side retainer oil seal.
  18762AA001 COMPRESSOR SPECIAL TOOL
  • Used for disassembling and installing the multi-plate clutch piston for shifting.
  • COMPRESSOR SPECIAL TOOL (18762AA000) can also be used.
  18765AA000 COMPRESSOR SUPPORT Used for disassembling and installing the multi-plate clutch for shifting.
  18763AA000 COMPRESSOR SHAFT Used for disassembling and installing the multi-plate clutch for shifting.
  28399SA010 OIL SEAL PROTECTOR Used for protecting oil seal when installing front drive shaft.
  18667AA010 HOLDER
  • Used for removing and installing the drive pinion lock nut.
  • Used as a holder to rotate gear when checking tooth contact.
  18270KA010 SOCKET (E16) Used for removing and installing the center support COMPL.
  18270KA020 SOCKET (E20)
  • Used for removing and installing the hypoid driven gear.
  • Used for removing and installing the drive pinion shaft retainer.
  398497701 SEAT Used for removing and installing the ball bearing.
  398177700 INSTALLER
  • Used for removing and installing the ball bearing and tapered roller bearing.
  • Used for installing the parking gear.
  398643600 GAUGE Used for measuring the total end play, extension end play and drive pinion height.
  899864100 REMOVER Used for removing and installing the ball bearing.
  498077000 REMOVER
  • Used for removing ball bearing of front reduction drive gear.
  • Used for removing the inner bearing inner race of the drive pinion shaft.
  • Used for removing the differential taper roller bearing.
  18657AA010 INSTALLER Used for installing the oil seal of inhibitor switch.
  18657AA020 OIL SEAL INSTALLER Used for installing the oil seal.
  18621AA000 ADAPTER WRENCH Used for removing and installing the drive pinion shaft lock nut.
  18651AA000 INSTALLER Used for installing the bearing of front reduction drive gear.
  18720AA000 REMOVER Used for removing ball bearing of reduction driven gear.
  498497300 CRANKSHAFT STOPPER Used for stopping the drive plate rotation when removing and installing the drive plate.
  20299AG010 PRESS SNAP RING Used for installing the bearing on primary pulley side.
  399513600 INSTALLER
  • Used for removing the ball bearing of the rear drive shaft.
  • Used for removing the bearing of the oil pump chain sprocket.
  499267300 STOPPER PIN Used for adjusting the inhibitor switch.
  499277100 BUSHING 1-2 INSTALLER
  • Used for installing the front differential taper roller bearing.
  • Used for removing and installing the transfer reduction drive gear.
  • Used for installing the ball bearing of the transfer reduction drive gear.
  • Used for installing the oil seal.
  • Used for installing the ball bearing of the transfer reduction driven gear.
  499277200 INSTALLER
  • Used for installing the inner bearing inner race of drive pinion shaft.
  • Used for installing the reduction driven gear.
  499575400 GAUGE Used for measuring height of end play.
  499737100 PULLER SET
  • Used for measuring height of forward clutch.
  • Used for measuring the transfer end play.
  • Use the rack only.
  499575600 GAUGE
  • Used for measuring height of forward clutch.
  • Used for measuring height of end play.
  499787700 WRENCH Used for measuring the differential pinion shaft backlash.
  499757002 INSTALLER Used for installing the bearing of front reduction driven gear.
  18767AA000 BEARING REMOVER
  • Used for removing the transfer reduction drive gear.
  • Used for removing the reduction driven gear bearing retainer.
  • Used for removing the front reduction driven shaft.
  499755602 PRESS SNAP RING
  • Used for installing the oil seal.
  • Used for installing the ball bearing and roller bearing.
  498077600 REMOVER
  • Used for removing the ball bearing of the rear drive shaft.
  • Used for removing the ball bearing of transfer reduction driven gear.
  • Used for removing ball bearing of reduction driven gear.
  • Used for removing the ball bearing of drive sprocket.
  18460AA040 CHECK BOARD Used for inspecting the TCM terminal.
  -
(Newly adopted tool)		 SUBARU SELECT MONITOR 4 Used for setting of each function and troubleshooting for electrical system.
NOTE: For detailed operation procedures of Subaru Select Monitor 4, refer to "Application help".
Fig 1: ST41099AJ010
G06651932Courtesy of SUBARU OF AMERICA, INC.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.