Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSUBARU2014OUTBACK 2.5I, STANDARD TRANSREPAIR AND DIAGNOSISBRAKESTRACTION CONTROLVEHICLE DYNAMICS CONTROL SYSTEM (DIAGNOSTICS)SUBARU SELECT MONITOROPERATIONFREEZE FRAME DATA
2014 Subaru Outback 2.5i, Standard Trans
Freeze Frame Data
2014 Subaru Outback 2.5i, Standard TransSECTION Freeze Frame Data
NOTE:
- Data stored at the time of trouble occurrence is shown on display.
- Each time a trouble occurs, the latest information is stored in the freeze frame data in memory.
- If a freeze frame data is not properly stored in memory (due to a drop in VDCCM power supply, etc.), a DTC suffixed with a question mark "?" appears on the Subaru Select Monitor display. This shows it may be an unreliable reading.
| Display | Contents to be displayed |
|---|---|
| FR Wheel Speed | Wheel speed detected by front ABS wheel speed sensor RH is displayed in km/h or MPH. |
| FL Wheel Speed | Wheel speed detected by front ABS wheel speed sensor LH is displayed in km/h or MPH. |
| RR Wheel Speed | Wheel speed detected by rear ABS wheel speed sensor RH is displayed in km/h or MPH. |
| RL Wheel Speed | Wheel speed detected by rear ABS wheel speed sensor LH is displayed in km/h or MPH. |
| Vehicle Speed | Vehicle speed calculated by VDC control module is displayed. |
| Steer Angle Sensor Op | Steering angle detected by steering angle sensor is displayed. |
| Yaw Rate Sensor Output | Vehicle angular speed detected by yaw rate sensor is displayed. |
| Master Cylinder Pressure Sensor | Master cylinder brake fluid pressure detected by pressure sensor is displayed. |
| FL Wheel Cylinder Pressure Sensor | For models with EyeSight, FL wheel cylinder brake fluid pressure detected by pressure sensor is displayed. (For models without EyeSight, 0 bar is always displayed.) |
| FR Wheel Cylinder Pressure Sensor | For models with EyeSight, FR wheel cylinder brake fluid pressure detected by pressure sensor is displayed. (For models without EyeSight, 0 bar is always displayed.) |
| Fr Rr G sensor Output | Vehicle longitudinal acceleration detected by longitudinal G sensor is displayed. |
| Lateral G sensor Output | Vehicle lateral acceleration detected by lateral G sensor is displayed. |
| ABS_CM Power Voltage | Voltage supplied to VDC control module is displayed. |
| Accel. Opening Angle | Acceleration opening is displayed. |
| Engine Speed | Engine speed on malfunction occurrence is displayed. |
| Steering angle flag | Whether the absolute angle of the steering angle sensor was determined is displayed. |
| EBD Control Flag | EBD control condition is displayed. |
| ABS Control Flag | ABS control condition is displayed. |
| TCS Control Flag | TCS control condition is displayed. |
| VDC Control Flag | VDC control condition is displayed. |
| E/G Control Stop Flag | Engine control command signal is displayed. |
| OFF Switch Detection | ON/OFF condition of the VDC operated by the driver is displayed. |
| Brake Switch | Brake ON/OFF is displayed. |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.