Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSUBARU2014LEGACY 2.5I, AUTOMATIC CVT TRANSREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 73 (POWER REAR GATE SYSTEM (DIAGNOSTICS))READ CURRENT DATALIST
2014 Subaru Legacy 2.5i, Automatic CVT Trans
Read Current Data: List
2014 Subaru Legacy 2.5i, Automatic CVT TransSECTION List
WARNING: This page is about a different car, the 2014 Subaru Forester. However, it is still accessible from the selected car via links, so may be relevant.
| Item Name | Content | Standard | Note |
|---|---|---|---|
| +POWER B | Power supply voltage value Display range: 0.00 - 21.5 V | 10.5 - 16 V | - |
| + B | PRG CM power supply voltage value Display range: 0.00 - 21.5 V | 10.5 - 16 V | - |
| IGN SW | Ignition switch status Display range: ON/OFF |
ON: IGN ON OFF: IGN OFF |
- |
| Memory stop SW | Memorized height switch status Display range: ON/OFF |
ON: switch ON OFF switch OFF |
- |
| D SW | Driver's seat switch status Display range: ON/OFF |
ON: switch ON OFF switch OFF |
- |
| R/G inner SW | PRG inner switch status Display range: ON/OFF |
ON: switch ON OFF switch OFF |
- |
| COURTESY SW | Courtesy switch status Display range: ON/OFF |
ON: switch ON OFF switch OFF |
- |
| LATCH SW | Latch switch status Display range: ON/OFF |
ON: switch ON OFF switch OFF |
- |
| SECTOR SW | Sector switch status Display range: ON/OFF |
ON: switch ON OFF switch OFF |
- |
| TOUCH SENSOR R | Right side touch sensor status Display range: ON/OFF |
ON: switch ON OFF switch OFF |
- |
| TOUCH SENSOR L | Left side touch sensor status Display range: ON/OFF |
ON: switch ON OFF switch OFF |
- |
| PRG MOTOR (OPEN) | Output status of rear gate motor open signal Display range: OPEN/OFF |
OPEN: when operating rear gate open OFF: OFF |
- |
| PRG MOTOR (CLOSE) | Output status of rear gate motor close signal Display range: CLOSE/OFF |
CLOSE: when operating rear gate close OFF: OFF |
- |
| CLUTCH(-) | Output status of drive unit clutch Display range: ON/OFF |
ON: when clutch OFF output OFF: OFF |
- |
| CLUTCH(+) | Output status of drive unit clutch Display range: ON/OFF |
ON: when clutch ON output OFF: OFF |
- |
| CLOSER (OPEN) | Output status of auto power rear gate closer motor open signal Display range: OPEN/OFF |
OPEN: when open output OFF: OFF |
- |
| CLOSER (CLOSE) | Output status of auto power rear gate closer motor close signal Display range: CLOSE/OFF |
CLOSE: when close output OFF: OFF |
- |
| BUZZER | Buzzer output status Display range: ON/OFF |
ON: when buzzer sounding OFF: when buzzer stopping |
- |
| HAZARD | Hazard output status Display range: ON/OFF |
ON: when hazard ON OFF: when hazard OFF |
- |
| Pulse-count | Drive unit count information Display range: 0 - 765 |
- | - |
| Connection Continuing Flag | Display range: Flag/not Flag | Flag: not Flag: |
- |
| PRG State | Rear gate status Display range: Fully open/Door free/Operating/Totally-enclosed |
Fully open: fully open status Door free: door free status Suspend: suspend status Operating: operating status Totally-enclosed: totally-enclosed status |
- |
| Idle Stop Cancel Flag | Status of Auto Start Stop cancel request Display range: Flag/not Flag |
Flag: when Auto Start Stop cancellation not Flag: when Auto Start Stop |
- |
| HALF STOP SOL (Lock) | Output status of stop holding solenoid lock signal Display range: ON/OFF |
ON: when solenoid lock output OFF: when not operating solenoid |
- |
| HALF STOP SOL (Cancel) | Output status of stop holding solenoid cancel signal Display range: ON/OFF |
ON: when solenoid cancel output OFF: when operating solenoid |
- |
| HALF STOP SOL POS SW | Display range: ON/OFF | ON: when stop holding OFF: when not stop holding |
- |
| IGN | Ignition switch status (body integrated unit) Display range: ON/OFF |
ON: IGN ON OFF: IGN OFF |
- |
| R/G Open SW | PRG opener switch status Display range: OFF/Short Push/Long Push |
OFF: when OFF Short Push: when operating Short Push Long Push: when operating Long Push |
- |
| Front Wheel Speed | Vehicle speed condition Display range: 0 - 229.5 km/h (0 - 142.6 MPH) |
Show vehicle speed | - |
| Normal Keyless R/G SW | Status of normal keyless R/G switch Display range: OFF/Short Push/Long Push |
OFF: when OFF Short Push: when operating Short Push Long Push: when operating Long Push |
- |
| Smart Keyless R/G SW | Status of keyless access key R/G switch Display range: OFF/Short Push/Long Push |
OFF: when OFF Short Push: when operating Short Push Long Push: when operating Long Push |
- |
| Idle Stop Control | Status of Auto Start Stop control Display range: Idle Stop Control/Idle Stop Uncontrol |
Idle Stop Control: when Idle Stop Control Idle Stop Uncontrol: other than Idle Stop Control |
- |
| P range SW | Status of shift lever P Display range: ON/OFF |
ON: when in P range OFF: when other than in P range |
- |
| Parking Brake Switch Input | Status of parking brake switch Display range: ON/OFF |
ON: when parking brake is ON OFF: when parking brake is OFF |
- |
| MT/AT | Vehicle information (body integrated unit) Display range: MT/AT |
MT: MT model AT: AT model |
- |
| R/G Open Authorized State | Status of PRG permission Display range: Authorized State/Unauthorized State |
Authorized State: PRG Open Authorized State Unauthorized State: PRG Open Unauthorized State |
- |
| Answer-Back Buzzer Information | Body integrated unit customizing information Display range: ON/OFF |
ON: when buzzer sounding ON OFF: when buzzer sounding OFF |
- |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.