SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSUBARU2014IMPREZA SPORT LIMITEDREPAIR AND DIAGNOSISBODY & FRAMEDOOR LOCKSKEYLESS ACCESS WITH PUSH BUTTON START SYSTEM (DIAGNOSTICS)DIAGNOSTICS WITH PHENOMENONINSPECTIONENGINE DOES NOT START
2014 Subaru Impreza Sport Limited

Engine Does Not Start

2014 Subaru Impreza Sport LimitedSECTION Engine Does Not Start
CAUTION:
  • When the keyless access control module is replaced with a new unit, and the battery ground terminal is connected, it will become ignition ON. Also, if the battery is disconnected, it will resume to a condition with the battery cut off.
  • When the keyless access control module or ID code box is replaced, registration of the immobilizer is required. For the relevant procedures, refer to the "REGISTRATION MANUAL FOR IMMOBILIZER".
Step Check Yes No
1 INITIALIZE STEERING LOCK  .
  1. Place the shift lever in the Parking range.
  2. Operate the driver's door switch ON/OFF with the ignition switch OFF.
  3. Wait for 10 seconds.
  4. Place the access key on the driver's seat.
  5. Press the push button ignition switch while depressing the brake pedal.
 Can the engine start? System is normal. Go to step 2  .
2 CHECK DTC  .
Read the DTC of the keyless access system using Subaru Select Monitor.		 Is DTC detected? Perform the diagnosis according to the DTC. < Ref. to LIST , List of Diagnostic Trouble Code (DTC).> Go to step 3  .
3 CHECK POWER SUPPLY SWITCHING  .
  1. Place the access key on the driver's seat.
  2. Press the push button ignition switch without depressing the brake pedal.
 When the switch is operated, does the < IG-OFF > → < ACC-ON > → < IG-ON > → < IG-OFF > change occur? Go to step 4  . Perform the diagnostics according to the symptom for power supply switching system in General Diagnostic Table. < Ref. to POWER SUPPLY SWITCHING SYSTEM , INSPECTION, General Diagnostic Table.>
4 CHECK CURRENT DATA  .
  1. Place the access key on the driver's seat.
  2. Press the push button ignition switch while depressing the brake pedal.
  3. Using the Subaru Select Monitor, confirm the keyless access CM, the current data «STSW signal monitor» when pressing the push button ignition switch.
    NOTE: If it is difficult to confirm, press and hold the push button ignition switch for approximately five seconds.
 Does the data change from OFF → ON? Go to step 10  . Go to step 5  .
5 CHECK CURRENT DATA  .
Check the keyless access CM, current data «Shift P Signal» using the Subaru Select Monitor.		 Is ON displayed in parking position, and OFF displayed in other positions? Go to step 6  . Go to step 11  .
6 CHECK CURRENT DATA  .
Confirm the keyless access CM, current data «Stop Light Switch» using the Subaru Select Monitor.		 Is ON displayed when brake pedal depressed, and OFF displayed when brake pedal not depressed? Go to step 7  . Go to step 13  .
7 CHECK CURRENT DATA  .
Confirm the keyless access CM, current data «Neutral SW/Clutch SW» using the Subaru Select Monitor.		 Is ON displayed in parking and neutral positions, and OFF displayed in other positions? Go to step 8  . Go to step 15  .
8 CHECK STEERING LOCK  .
Operate the push button ignition switch to perform the power supply switching and check steering lock condition during ACC-ON condition.		 Is the steering lock in unlocked condition? Go to step 9  . Perform the diagnostics according to the symptom for steering lock system in General Diagnostic Table. < Ref. to STEERING LOCK SYSTEM , INSPECTION, General Diagnostic Table.>
9 CHECK KEYLESS ACCESS CM  .
  1. Turn the ignition switch to OFF.
  2. Disconnect the ECM connector.
  3. Using a tester, measure the battery voltage in following procedures.
    1. Press the push button ignition switch with the brake pedal depressed. (Measure within 10 seconds.)
    2. Release the push button ignition switch from the condition of step  1 above.

      Connector & terminal 

      (B572) No. 13 (+) - Chassis ground (-): 

 Does the value change from 1 V or less to +B-2 V or more in the step 1, and return to 1 V or less in the step 2? Perform the diagnosis for engine system. < Ref. to DIAGNOSTICS FOR ENGINE STARTING FAILURE .> Replace the keyless access CM. < Ref. to KEYLESS ACCESS CM .>
10 CHECK CURRENT DATA  .
  1. Connect the disconnected connectors.
  2. Confirm the keyless access CM, current data «Engine start permission request reception status» using the Subaru Select Monitor.
 Is "Reception" displayed with ignition switch ON, and "Not yet received" displayed in other positions? Perform the diagnosis for engine system. Replace the keyless access CM. < Ref. to KEYLESS ACCESS CM .>
11 CHECK "P" RANGE SWITCH  .
  1. Turn the ignition switch to OFF.
  2. Disconnect the AT shift lever connector.
  3. Using a tester, check the continuity of "P" range switch.

    Connector & terminal 

    (B116) No. 1 - 2: 

 Does it change from Continuity ←→ No continuity according to shift lever operation? Go to step 12  . Replace the "P" range switch. < Ref. to REMOVAL , AT Shift Lock Solenoid and "P" Range Switch.>
12 CHECK HARNESS  .
  1. Turn the ignition switch to OFF.
  2. Disconnect the keyless access CM connector.
  3. Using a tester, check continuity between the keyless access CM and AT select lever.

    Connector & terminal 

    (B116) No. 1 - (B574) No. 25: 

    (B116) No. 2 - Chassis ground: 

 Is there continuity? Replace the keyless access CM. < Ref. to KEYLESS ACCESS CM .> Repair or replace the harness.
13 CHECK STOP LIGHT SWITCH  .
  1. Turn the ignition switch to OFF.
  2. Disconnect the stop light switch connector.
  3. Using a tester, check the continuity of the stop light switch.

    Connector & terminal 

    (B65) No. 3 - No. 4: 

 Does ←→ No continuity according to brake pedal operation? Go to step 14  . Replace the stop light switch. < Ref. to REMOVAL , Stop Light Switch.>
14 CHECK HARNESS  .
  1. Turn the ignition switch to OFF.
  2. Using a tester, check continuity between the keyless access CM and stop light switch.

    Connector & terminal 

    (B572) No. 18 - (B65) No. 2: 

    (B65) No. 1 - F/B fuse No. 8: 

 Is there continuity? Replace the keyless access CM. < Ref. to KEYLESS ACCESS CM .> Repair or replace the harness.
15 CHECK INHIBITOR SWITCH  .
Check the inhibitor switch. < Ref. to INSPECTION , Inhibitor Switch.>		 Is the inhibitor switch working normal? Go to step 16  . Replace the inhibitor switch. < Ref. to REMOVAL , Inhibitor Switch.>
16 CHECK HARNESS  .
  1. Turn the ignition switch to OFF.
  2. Disconnect the inhibitor switch connector.
  3. Using a tester, check continuity between the keyless access CM connector and inhibitor switch connector.

    Connector & terminal 

    (B572) No. 5 - (B12) No. 16: 

    (B12) No. 15 - Starter motor: 

 Is there continuity? Replace the keyless access CM. < Ref. to KEYLESS ACCESS CM .> Repair or replace the harness.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.