SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSUBARU2014IMPREZA SPORT LIMITEDREPAIR AND DIAGNOSISACCESSORIES & EQUIPMENTCOMMUNICATION DEVICESBODY CONTROL SYSTEM (DIAGNOSTICS)USER CUSTOMIZINGOPERATION
2014 Subaru Impreza Sport Limited

User Customizing: Operation

2014 Subaru Impreza Sport LimitedSECTION Operation
  1. On «Main Menu» display, select {Each System Check}.
  2. On «System Selection Menu» display, select {Integ. unit mode}.
  3. On «Integ. unit mode failure diag.» display, select {Work Support}.
  4. On «Work Support» display, select {Unit customizing}.
  5. Change the setting with UP/DOWN key and set with the [OK] key.

    List of User Customizing item

    Data Initial setting value Customize setting Remarks
    Off delay time 30s OFF Room light off delay time can be selected.
    10 Sec
    20 Sec
    30s
    Auto Light Sensitivity Adjustment Normal Dull Slow response
    Normal Standard
    Sensitive Quick response
    Very sensitive Fairly quick response
    Power rear gate setting -
    ((1))    		 ON Fixed at OFF because this is not applicable.
    OFF
    Back auto rear wiper setting OFF ON Fixed at OFF because this is not applicable.
    OFF
    TPMS Setting -
    ((1))    		 TPMS Set to "ON" for model with TPMS.
    No TPMS
    Driver's door select unlock ALL Select ALL fixed (impossible to change)
    ALL
    R gate select unlock ALL Select ALL fixed (impossible to change)
    ALL
    Rear defogger operation mode Normal Normal Automatically stops in 15 minutes after switch is turned to ON.
    Continuous Repeats active condition for 15 minutes and inactive condition for 2 minutes until switch is turned to OFF.
    Security Alarm Setup ON ON Security alarm (hazard, horn or siren) in active condition
    OFF Security alarm in inactive condition
    Impact Sensor Setup OFF ON Workable when the "Impact sensor" is set to "ON". Impact sensor function becomes activated.
    OFF Impact sensor in inactive condition (Set to "OFF" in models without sensors.)
    Alarm delay setup ON   After the keyless lock operation, the alarm monitor starts after the following delay time has passed.
    ON Delay time is 30 seconds.
    OFF Delay time is 0 seconds.
    Lockout prevention ON ON key lockout prevention function is activated. (The function does not operate if safety knob is locked by hand.)
    OFF Key lockout prevention function is deactivated.
    Impact sensor (OP) OFF ON Vehicle is controlled in impact sensor equipped mode. (Make sure to set to "OFF" for models without the impact sensor. When "ON", hazard, horn or siren become activated by keyless lock (alarm monitor start).)
    OFF Vehicle is controlled in no impact sensor mode.
    Buzzer sounding setting ON ON When lock/unlock is selected by keyless entry system operation, buzzer operates.
    OFF When lock/unlock is selected by keyless entry system operation, buzzer does not operate.
    Abnormal warning lamp flashing setting ON ON When lock/unlock is selected by keyless entry system operation, hazard blinks.
    OFF When lock/unlock is selected by keyless entry system operation, hazard does not interlock.
    Passive Alarm OFF ON  
    OFF  
    Door open warning ON ON  
    OFF  
    Dome Light Alarm Setting OFF ON Room light illuminates interlocking with alarm.
    OFF Room light does not illuminate interlocking with alarm.
    Auto A/C ECU Setting - ON Diagnoses with auto A/C CM.
    OFF Diagnoses without auto A/C CM.
    wiperdeicer - ON Wiper deicer control is performed.
    OFF Wiper deicer control is not performed.
    Illumination Control On/Off ON ON  
    OFF  
    Sedan/Wagon Setting - Sedan Body control is performed by Sedan.
    Wagon Body control is performed by Wagon.
    MT/AT Setting - MT Body control is performed by MT.
    AT Body control is performed by AT.
    6MT Setting - 6MT Body control is performed by 6MT.
    Other than 6MT Body control is performed by other than 6MT.
    Illumination Sensor Setting -
    ((1))    		 ON Set to "ON" for model with auto light.
    OFF
    Factory initial setting Market Market Customize setting is reset when mode is switched from Market to Factory.
    Factory
    (1) Customization item according to the actual vehicle equipment
  6. After setting, make sure that the setting changed in the {Current Data Display & Save} is same as vehicle equipment.
    CAUTION:
    • The above settings must match the actual vehicle equipment.
    • Do not change settings except for setting above while setting the functions.
    • Be sure not to change Factory initial setting except when installing a new body integrated unit.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.