System Operation Check Mode: List

2014 Subaru Forester 2.5i, Eng CD FB25BA, Standard TransSECTION List

Combination meter

Check item Item 1 Item 2 Note
Pointer operation check Speedometer Speedometer 0 km/h (MPH) indication -
Speedometer 40 km/h (MPH) indication -
Speedometer 80 km/h (MPH) indication -
Speedometer 120 km/h (MPH) indication -
Speedometer 160 km/h (MPH) indication -
Speedometer 200 km/h (MPH) indication -
Speedometer 240 km/h (MPH) indication -
Tachometer Tachometer 0 rpm indication -
Tachometer 1000 rpm indication -
Tachometer 2000 rpm indication -
Tachometer 3000 rpm indication -
Tachometer 4000 rpm indication -
Tachometer 5000 rpm indication -
Tachometer 6000 rpm indication -
Tachometer 7000 rpm indication -
Segment of liquid crystal display check LCD display all lighted -
AT shift
(For CVT only)
P range display -
R range display -
N range display -
L range display -
↑ display -
↓ display -
8 range display -
7 range display -
6 range display -
5 range display -
4 range display -
3 range display -
2 range display -
1 range display -
Odometer Odometer numerical device display 0 -
Odometer numerical device display 1 -
Odometer numerical device display 2 -
Odometer numerical device display 3 -
Odometer numerical device display 4 -
Odometer numerical device display 5 -
Odometer numerical device display 6 -
Odometer numerical device display 7 -
Odometer numerical device display 8 -
Odometer numerical device display 9 -
Trip meter Trip meter numerical device display 0 -
Trip meter numerical device display 1 -
Trip meter numerical device display 2 -
Trip meter numerical device display 3 -
Trip meter numerical device display 4 -
Trip meter numerical device display 5 -
Trip meter numerical device display 6 -
Trip meter numerical device display 7 -
Trip meter numerical device display 8 -
Trip meter numerical device display 9 -
Fuel gauge bar display Fuel sender E-point command -
Meter E scale command -
Fuel warning lit position command (fuel warning also lights) -
Meter 1/4 scale command -
Meter 1/2 scale command -
Meter 3/4 scale command -
Meter F-scale command -
Fuel sender F-point command -
Shift-up indicator (For MT model only) -
CRUISE indicator -
SET indicator -
Lamp check All lamps lit -
Indicator drive High-beam indicator -
Position light indicator
(For high-class meter/high-grade meter)
-
Front fog light indicator -
Water temperature (COOL) indicator -
VDC OFF indicator -
VDC operation/failure indicator -
Hill start assist OFF/failure indicator -
Warning drive Driver side seat belt warning -
Airbag warning -
All seats door warning -
Water temperature (HOT) warning -
E/G remaining oil warning -
AT (CVT) oil temperature warning (For CVT only) -
ABS warning -
BRAKE warning -
AWD warning
(For CVT only)
-
DPF clogging warning
(For diesel only)
-
Remaining washer fluid washer -
Remaining fuel warning -
EPS warning -
Diesel over-rev indicator
(For diesel only)
-
Check E/G warning -
Multi-Function Display (MFD) output check Passenger side seat belt warning -
Momentary fuel efficiency display value -
Mean fuel efficiency A display value -
Mean fuel efficiency B display value -
Remaining fuel cruising distance display value -
External air temperature indication value -
Mean vehicle speed display value -
Buzzer output Sounding output ON/OFF -
Illumination check Brightness check -
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.