Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSUBARU2014FORESTER 2.5I, ENG CD FB25BA, STANDARD TRANSREPAIR AND DIAGNOSIS (SINGLE PAGE)BRAKESTRACTION CONTROLVEHICLE DYNAMICS CONTROL (DIAGNOSTICS)SUBARU SELECT MONITOROPERATIONREAD CURRENT DATA
2014 Subaru Forester 2.5i, Eng CD FB25BA, Standard Trans
Read Current Data
2014 Subaru Forester 2.5i, Eng CD FB25BA, Standard TransSECTION Read Current Data
For detailed operation procedures, refer to "PC application help for Subaru Select Monitor".
| Display | Contents to be displayed | Unit of measure |
|---|---|---|
| FR Wheel Speed | Wheel speed detected by front ABS wheel speed sensor RH is displayed. | km/h or MPH |
| FL Wheel Speed | Wheel speed detected by front ABS wheel speed sensor LH is displayed. | km/h or MPH |
| RR Wheel Speed | Wheel speed detected by rear ABS wheel speed sensor RH is displayed. | km/h or MPH |
| RL Wheel Speed | Wheel speed detected by rear ABS wheel speed sensor LH is displayed. | km/h or MPH |
| Steering Angle Sensor | Steering angle detected by steering angle sensor is displayed. | deg |
| Yaw Rate Sensor | Vehicle angular speed detected by yaw rate sensor is displayed. | deg/s |
| Pressure Sensor | Brake fluid pressure detected by pressure sensor is displayed. | bar |
| Longitudinal G Sensor | Vehicle longitudinal acceleration detected by longitudinal G sensor is displayed. | m/s2 |
| Lateral G Sensor | Vehicle lateral acceleration detected by lateral G sensor is displayed. | m/s2 |
| Voltage of IGN | Voltage supplied to VDCCM & H/U is displayed. | V |
| M. Relay monitor Voltage | Voltage applied to the motor relay is displayed. | V |
| FL wheel cylinder pressure sensor output | FL wheel cylinder brake fluid pressure detected by pressure sensor is displayed. | bar |
| FR wheel cylinder pressure sensor output | FR wheel cylinder brake fluid pressure detected by pressure sensor is displayed. | bar |
| Motor Relay Signal | Motor relay driving signal is displayed. | ON or OFF |
| Valve Relay Signal | Valve relay driving signal is displayed. | ON or OFF |
| EBD Warning Light | ON operation of the EBD warning light is displayed. | ON or OFF |
| ABS Warning Lamp | ON operation of the ABS warning light is displayed. | ON or OFF |
| VDC Warning Lamp | ON operation of the VDC warning light is displayed. | ON or OFF |
| EBD Control Flag | EBD operation condition is displayed. | ON or OFF |
| ABS Control Flag | ABS operation condition is displayed. | ON or OFF |
| TCS Control Flag | TCS operation condition is displayed. | ON or OFF |
| VDC Control Flag | VDC operation condition is displayed. | ON or OFF |
| E/G Control Stop Flag | Engine control command signal is displayed. | 1 or 0 |
| Stop-lamp relay drive signal | Brake light relay driving signal is displayed. | ON or OFF |
| X Mode | The status of X MODE is displayed. | ON or OFF |
| VDC-OFF Light | ON/OFF condition of VDC OFF indicator light is displayed. | ON or OFF |
| OFF SW Signal | Operation condition of VDC OFF switch is displayed. | ON or OFF |
| Brake Light Switch | Brake ON/OFF is displayed. | ON or OFF |
| Clutch Switch | Clutch ON/OFF is displayed. (For MT model only. For AT model: OFF fixed) | ON or OFF |
| Reverse Signal | Reverse gear ON/OFF is displayed. (For MT model only. For AT model: OFF fixed) | ON or OFF |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.