SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSUBARU2014FORESTER 2.5I PREMIUM, ENG CD FB25BC, AUTOMATIC CVT TRANSREPAIR AND DIAGNOSISTRANSMISSIONMANUAL TRANSTRANSMISSION CONTROL SYSTEMSAT SHIFT LOCK CONTROL SYSTEMELECTRICAL SPECIFICATION
2014 Subaru Forester 2.5i Premium, Eng CD FB25BC, Automatic CVT Trans

Electrical Specification

2014 Subaru Forester 2.5i Premium, Eng CD FB25BC, Automatic CVT TransSECTION Electrical Specification
Fig 1: AT Shift Lock Control Module Connector Terminal Identification
G08317518Courtesy of SUBARU OF AMERICA, INC.
  • Model without push button ignition switch
    Item Connector No. Terminal No. Input/Output signal
    Measured value and measuring conditions
    Battery power supply B281 6 9 - 16 V
    7
    i84 6
    Ignition power supply B280 32 10 - 15 V when ignition switch is at ACC.
    B281 3 10 - 15 V when ignition switch is at ON or START.
    TCM ("P" range) i84 27 Can not be measured because of digital communication
    35
    Stop light and brake switch B280 10 9 - 16 V when the stop light & brake switch is ON.
    0 V when the stop light & brake switch is OFF.
    "P" range switch B281 18 0 V when select lever is in "P" range.
    9 - 16 V when select lever is in other positions than "P" range.
    Solenoid unit signal B281 5 8.5 - 16 V when shift lock is released.
    0 V when shift lock is operating.
    Key warning switch signal B280 4 9 - 16 V when key is inserted.
    0 V when key is removed.
    Key lock solenoid signal B281 4 7.5 - 16 V when the key is inserted with the select lever shifted in positions other than "P" range.
    0 V at other conditions than above.
    Ground B280 1 -
    B281 31
  • Model with push button ignition switch
    Item Connector No. Terminal No. Input/Output signal
    Measured value and measuring conditions
    Battery power supply B281 6 9 - 16 V
    7
    i84 6
    Ignition power supply B280 32 10 - 15 V when ignition switch is at ACC.
    B281 3 10 - 15 V when ignition switch is at ON or START.
    TCM ("P" range) i84 27 Can not be measured because of digital communication
    35
    Stop light and brake switch B280 10 9 - 16 V when the stop light & brake switch is ON.
    0 V when the stop light & brake switch is OFF.
    "P" range switch B281 18 0 V when select lever is in "P" range.
    9 - 16 V when select lever is in other positions than "P" range.
    Solenoid unit signal B281 5 8.5 - 16 V when shift lock is released.
    0 V when shift lock is operating.
    Ground B280 1 -
    B281 31
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.