Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSUBARU1998LEGACY BRIGHTON WAGON AWD F4-2.2L SOHCREPAIR AND DIAGNOSISSPECIFICATIONSMECHANICAL SPECIFICATIONSSTEERINGPOWER STEERING PUMP
1998 Subaru Legacy Brighton Wagon AWD F4-2.2L SOHC
Power Steering Pump
1998 Subaru Legacy Brighton Wagon AWD F4-2.2L SOHCSECTION Power Steering Pump
GENERAL SPECIFICATIONS
Output 7.2 cm3 (0.439 cu. inch)
Range Of Revolution 500 - 7,500 rpm
Revolving Direction Clockwise
Hydraulic Fluid Control: Dropping In Response To Increased Engine Revolutions
Pulley Shaft:
Radial Play 0.4 mm (0.016 inch) Or Less
Axial Play 0.9 mm (0.035 inch) Or Less
Pulley:
Ditch Deflection 1.0 mm (0.039 inch) Or Less
Resistance To Rotation 9.22 N (2.07 lbs.) Or Less
TORQUE SPECIFICATIONS
Support Bracket Mounting Bolts 22.0 ± 2.0 Nm (15.90 ± 1.40 ft. lbs.)
Pump To Bracket Bolts 20.1 ± 2.5 Nm (14.80 ± 1.80 ft. lbs.)
Pulley Nut 60.8 ± 6.9 Nm (44.80 ± 5.10 ft. lbs.)
Tank Mounting Bolts:
Outside 15.7 ± 2.4 Nm (11.58 ± 1.77 ft. lbs.)
Inside 18.1 ± 2.5 Nm (13.35 ± 1.84 ft. lbs.)
Adjuster Bolt:
Vertical 8.0 ± 2.0 Nm (69.60 ± 16.80 inch lbs.)
Horizontal 24.5 ± 2.0 Nm (18.07 ± 1.48 ft. lbs.)
Belt Cover:
Vertical Bolts 13.0 ± 3.0 Nm (112.80 ± 26.40 inch lbs.)
Horizontal 24.5 ± 2.0 Nm (18.07 ± 1.48 ft. lbs.)
Pump Connector 74.0 ± 5.0 Nm (54.20 ± 3.60 ft. lbs.)
Rear Cover Bolts 16.0 ± 2.0 Nm (11.60 ± 1.40 ft. lbs.)
Output 7.2 cm3 (0.439 cu. inch)
Range Of Revolution 500 - 7,500 rpm
Revolving Direction Clockwise
Hydraulic Fluid Control: Dropping In Response To Increased Engine Revolutions
Pulley Shaft:
Radial Play 0.4 mm (0.016 inch) Or Less
Axial Play 0.9 mm (0.035 inch) Or Less
Pulley:
Ditch Deflection 1.0 mm (0.039 inch) Or Less
Resistance To Rotation 9.22 N (2.07 lbs.) Or Less
TORQUE SPECIFICATIONS
Support Bracket Mounting Bolts 22.0 ± 2.0 Nm (15.90 ± 1.40 ft. lbs.)
Pump To Bracket Bolts 20.1 ± 2.5 Nm (14.80 ± 1.80 ft. lbs.)
Pulley Nut 60.8 ± 6.9 Nm (44.80 ± 5.10 ft. lbs.)
Tank Mounting Bolts:
Outside 15.7 ± 2.4 Nm (11.58 ± 1.77 ft. lbs.)
Inside 18.1 ± 2.5 Nm (13.35 ± 1.84 ft. lbs.)
Adjuster Bolt:
Vertical 8.0 ± 2.0 Nm (69.60 ± 16.80 inch lbs.)
Horizontal 24.5 ± 2.0 Nm (18.07 ± 1.48 ft. lbs.)
Belt Cover:
Vertical Bolts 13.0 ± 3.0 Nm (112.80 ± 26.40 inch lbs.)
Horizontal 24.5 ± 2.0 Nm (18.07 ± 1.48 ft. lbs.)
Pump Connector 74.0 ± 5.0 Nm (54.20 ± 3.60 ft. lbs.)
Rear Cover Bolts 16.0 ± 2.0 Nm (11.60 ± 1.40 ft. lbs.)
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.