Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSUBARU1998LEGACY BRIGHTON WAGON AWD F4-2.2L SOHCREPAIR AND DIAGNOSISCRUISE CONTROLTESTING AND INSPECTIONSYMPTOM RELATED DIAGNOSTIC PROCEDURESDESCRIPTION OF ON-BOARD DIAGNOSTICSDIAGNOSTICS CHART WITH SELECT MONITOR
1998 Subaru Legacy Brighton Wagon AWD F4-2.2L SOHC
Diagnostics Chart with Select Monitor
1998 Subaru Legacy Brighton Wagon AWD F4-2.2L SOHCSECTION Diagnostics Chart with Select Monitor
FUNCTION MODE
NOTE: Applicable select monitor cartridge: No.24082AA010
Select the "Cruise Control" system using the select monitor and set the "Current Data Display & Save" mode. The following parameters will then appear on the display.
- Vehicle Speed
The current vehicle speed is shown on the display.
- Stop Lamp Switch
When the brake pedal is depressed, the stop lamp switch shown on the display turns from "OFF" to "ON"
- Brake Switch
When the brake pedal is depressed, the brake switch shown on the display turns from "OFF" to "ON"
- "SET/COAST" Switch
When the cruise control command switch is placed in the "SET/COAST" position, the SET/COAST switch shown on the display turns from "OFF" to "ON"
- "RESUME/ACCEL" Switch
When the cruise control command switch is placed in the "RESUME/ACCEL" position, the RESUME/ ACCEL switch shown on the display turns from "OFF" to "ON".
- Clutch/Inhibitor Switch
When the clutch pedal is depressed, the clutch/ inhibitor switch shown on the display turns from "ON" to "OFF". (MT)
When the selector lever is moved from the "N" or "P" position to any other position, the clutch/ inhibitor switch shown on the display turns from "ON" to "OFF". (AT)
NOTE: Applicable select monitor cartridge: No.24082AA010
Select the "Cruise Control" system using the select monitor and set the "Current Data Display & Save" mode. The following parameters will then appear on the display.
- Vehicle Speed
The current vehicle speed is shown on the display.
- Stop Lamp Switch
When the brake pedal is depressed, the stop lamp switch shown on the display turns from "OFF" to "ON"
- Brake Switch
When the brake pedal is depressed, the brake switch shown on the display turns from "OFF" to "ON"
- "SET/COAST" Switch
When the cruise control command switch is placed in the "SET/COAST" position, the SET/COAST switch shown on the display turns from "OFF" to "ON"
- "RESUME/ACCEL" Switch
When the cruise control command switch is placed in the "RESUME/ACCEL" position, the RESUME/ ACCEL switch shown on the display turns from "OFF" to "ON".
- Clutch/Inhibitor Switch
When the clutch pedal is depressed, the clutch/ inhibitor switch shown on the display turns from "ON" to "OFF". (MT)
When the selector lever is moved from the "N" or "P" position to any other position, the clutch/ inhibitor switch shown on the display turns from "ON" to "OFF". (AT)
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.