SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSCION2016IM AUTOMATIC CVT TRANSREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT VARIANT/TRIMSECTION 2 (MANUAL TRANSMISSION - SERVICE INFORMATION)TRANSMISSION CONTROL CABLEADJUSTMENT [06/2015 - ]PROCEDURE
2016 Scion iM Automatic CVT Trans

Adjustment [06/2015 - ]: Procedure

2016 Scion iM Automatic CVT TransSECTION Procedure
WARNING: This page is about a different variant/trim than selected.
  1. REMOVE NO. 2 CYLINDER HEAD COVER 

    Refer to PROCEDURE - Step 15

  2. REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE 

    Refer to PROCEDURE - Step 3

  3. REMOVE AIR CLEANER CASE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 17

  4. REMOVE REAR CONSOLE BOX ASSEMBLY 

    Refer to REMOVAL [06/2015 - ]

  5. ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY 
    1. Remove the clip and disconnect the transmission control select cable from the floor shift lever assembly.
      GTY428624Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Push the 2 claws together at the top of the lock piece. While holding the 2 claws together, push the 2 lugs on the bottom of the lock piece toward each other and upward to push out the lock piece.
      GTY491557Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Bottom View *b Push
      *c Push Out *d Lock Piece
    3. Hook the outer select lever of the manual transaxle assembly to the reverse restrict pin assembly to secure it.
      GTY452257Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Outer Select Lever
      *2 Reverse Restrict Pin Assembly
      *a Secured
    4. Push the slider shaft until it contacts the cam wall.
      NOTE:
      • Do not pull up the slider shaft.
      • When adjusting the transmission control cable assembly, make sure that the shift lever is not in the 1st or 2nd gear position.
      GTY484797Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Slider Shaft
      *b Cam Wall
    5. Connect the transmission control select cable to the floor shift lever assembly with the clip.
      GTY426520Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Transmission Control Select Cable
      *b Lock Piece
      NOTE:
      • Make sure that the lock piece is protruding from the adjuster case.
      • When adjusting the transmission control cable assembly, make sure that the shift lever is not in the 1st or 2nd gear position.
    6. Push the lock piece into the adjuster case.
      NOTE:

      Securely push in the lock piece until the lock is engaged.

    7. Move the shift lever to R, so that the outer select lever can be released.
      GTY447807Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Outer Select Lever
      *2 Reverse Restrict Pin Assembly
      *a Released
  6. INSTALL REAR CONSOLE BOX ASSEMBLY 

    Refer to INSTALLATION [06/2015 - ]

  7. INSTALL AIR CLEANER CASE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 55

  8. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE 

    Refer to PROCEDURE - Step 3

  9. INSTALL NO. 2 CYLINDER HEAD COVER 

    Refer to PROCEDURE - Step 82

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.