Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DBβ LIVE
HOMESERVICE MANUALSSCION2006XB L4-1.5L (1NZ-FE)REPAIR AND DIAGNOSISSPECIFICATIONSMECHANICAL SPECIFICATIONSENGINECYLINDER BLOCK ASSEMBLYPISTON, ENGINE
2006 Scion xB L4-1.5L (1NZ-FE)
Piston, Engine
2006 Scion xB L4-1.5L (1NZ-FE)SECTION Piston, Engine
Piston
Standard diameter 74.945 to 74.955 mm (2.9506 to 2.9510 inch)
Oil clearance
Standard 0.055 to 0.078 mm (0.0022 to 0.0031 inch)
Maximum 0.08 mm (0.0032 inch)
Standard pin hole diameter 18.013 to 18.016 mm (0.7092 to 0.7093 inch) at 20οΏ½C (68οΏ½F)
Standard ring groove clearance
No. 1 ring 0.02 to 0.04 mm (0.0008 to 0.0016 inch)
No. 2 ring 0.01 to 0.03 mm (0.0004 to 0.0012 inch)
No. 3 ring 0.01 to 0.03 mm (0.0004 to 0.0012 inch)
Piston Pin
Standard diameter 18.001 to 18.004 mm (0.7087 to 0.7088 inch)
Oil clearance
Standard 0.009 to 0.015 mm (0.0004 to 0.0006 inch)
Maximum 0.050 mm (0.0020 inch)
Piston Rings
Standard end gap
No. 1 ring 0.25 to 0.35 mm (0.0098 to 0.0138 inch)
No. 2 ring 0.35 to 0.50 mm (0.0138 to 0.0197 inch)
Oil ring 0.10 to 0.35 mm (0.0039 to 0.0138 inch)
Maximum end gap
No. 1 ring 0.91 mm (0.0358 inch)
No. 2 ring 1.06 mm (0.0417 inch)
Oil ring 0.82 mm (0.0323 inch)
Standard diameter 74.945 to 74.955 mm (2.9506 to 2.9510 inch)
Oil clearance
Standard 0.055 to 0.078 mm (0.0022 to 0.0031 inch)
Maximum 0.08 mm (0.0032 inch)
Standard pin hole diameter 18.013 to 18.016 mm (0.7092 to 0.7093 inch) at 20οΏ½C (68οΏ½F)
Standard ring groove clearance
No. 1 ring 0.02 to 0.04 mm (0.0008 to 0.0016 inch)
No. 2 ring 0.01 to 0.03 mm (0.0004 to 0.0012 inch)
No. 3 ring 0.01 to 0.03 mm (0.0004 to 0.0012 inch)
Piston Pin
Standard diameter 18.001 to 18.004 mm (0.7087 to 0.7088 inch)
Oil clearance
Standard 0.009 to 0.015 mm (0.0004 to 0.0006 inch)
Maximum 0.050 mm (0.0020 inch)
Piston Rings
Standard end gap
No. 1 ring 0.25 to 0.35 mm (0.0098 to 0.0138 inch)
No. 2 ring 0.35 to 0.50 mm (0.0138 to 0.0197 inch)
Oil ring 0.10 to 0.35 mm (0.0039 to 0.0138 inch)
Maximum end gap
No. 1 ring 0.91 mm (0.0358 inch)
No. 2 ring 1.06 mm (0.0417 inch)
Oil ring 0.82 mm (0.0323 inch)
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.