Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSCION2006XB L4-1.5L (1NZ-FE)REPAIR AND DIAGNOSISRESTRAINTS AND SAFETY SYSTEMSSEAT BELT SYSTEMSSERVICE AND REPAIR
2006 Scion xB L4-1.5L (1NZ-FE)
Seat Belt Systems: Service and Repair
2006 Scion xB L4-1.5L (1NZ-FE)SECTION Service and Repair
REMOVAL
HINT:
- Use the same procedures for the RH side and LH side.
- The procedures listed below are for the RH side.
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
2. REMOVE SEAT TRACK OUTER COVER RH
3. REMOVE SEAT TRACK BRACKET COVER INNER RH
4. REMOVE FRONT SEAT ASSEMBLY RH
5. REMOVE FRONT SEAT INNER BELT ASSEMBLY RH
a. Remove the bolt and inner belt.
INSTALLATION
HINT:
- Use the same procedures for the RH side and LH side.
- The procedures listed below are for the RH side.
- A bolt without a torque specification is shown in the standard bolt chart.
1. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH
a. Install the inner belt with the bolt.
Torque: 42 N.m (428 kgf.cm, 31 ft.lbf)
2. INSTALL FRONT SEAT ASSEMBLY RH
3. INSTALL SEAT TRACK BRACKET COVER INNER RH
4. INSTALL SEAT TRACK OUTER COVER RH
5. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
HINT:
- Use the same procedures for the RH side and LH side.
- The procedures listed below are for the RH side.
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
2. REMOVE SEAT TRACK OUTER COVER RH
3. REMOVE SEAT TRACK BRACKET COVER INNER RH
4. REMOVE FRONT SEAT ASSEMBLY RH
5. REMOVE FRONT SEAT INNER BELT ASSEMBLY RH
a. Remove the bolt and inner belt.
INSTALLATION
HINT:
- Use the same procedures for the RH side and LH side.
- The procedures listed below are for the RH side.
- A bolt without a torque specification is shown in the standard bolt chart.
1. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH
a. Install the inner belt with the bolt.
Torque: 42 N.m (428 kgf.cm, 31 ft.lbf)
2. INSTALL FRONT SEAT ASSEMBLY RH
3. INSTALL SEAT TRACK BRACKET COVER INNER RH
4. INSTALL SEAT TRACK OUTER COVER RH
5. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.