Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSCION2006XB L4-1.5L (1NZ-FE)REPAIR AND DIAGNOSISBODY AND FRAMEMIRRORSSERVICE AND REPAIROUTER REAR VIEW MIRROR
2006 Scion xB L4-1.5L (1NZ-FE)
Outer Rear View Mirror
2006 Scion xB L4-1.5L (1NZ-FE)SECTION Outer Rear View Mirror
REMOVAL
HINT:
- Use the same procedures for the RH side and LH side.
- The procedures listed below are for the LH side.
1. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH
2. REMOVE DOOR PULL HANDLE
3. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
4. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
5. REMOVE FRONT DOOR SERVICE HOLE COVER LH
6. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH
a. Disconnect the connector.
b. Remove the 3 nuts and mirror.
INSTALLATION
HINT:
- Use the same procedures for the RH side and LH side.
- The procedures listed below are for the LH side.
1. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH
a. Install the mirror with the 3 nuts.
Torque: 8.0 N.m (82 kgf.cm, 71 in.lbf)
b. Connect the connector.
2. INSTALL FRONT DOOR SERVICE HOLE COVER LH
3. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
4. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
5. INSTALL DOOR PULL HANDLE
6. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH
HINT:
- Use the same procedures for the RH side and LH side.
- The procedures listed below are for the LH side.
1. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH
2. REMOVE DOOR PULL HANDLE
3. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
4. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
5. REMOVE FRONT DOOR SERVICE HOLE COVER LH
6. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH
a. Disconnect the connector.
b. Remove the 3 nuts and mirror.
INSTALLATION
HINT:
- Use the same procedures for the RH side and LH side.
- The procedures listed below are for the LH side.
1. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH
a. Install the mirror with the 3 nuts.
Torque: 8.0 N.m (82 kgf.cm, 71 in.lbf)
b. Connect the connector.
2. INSTALL FRONT DOOR SERVICE HOLE COVER LH
3. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
4. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
5. INSTALL DOOR PULL HANDLE
6. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.