Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSATURN2010VUE XE, 2.4 1REPAIR AND DIAGNOSISQUICK LOOKUPSCOMMON SPECS & PROCEDURESCOMMON SPECS AND PROCEDURESSPECIFICATIONS INDEX
2010 Saturn Vue XE, 2.4 1
Specifications Index
2010 Saturn Vue XE, 2.4 1SECTION Specifications Index
VUE SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM SPECIFICATIONS | ||
| Torque | Automatic FASTENER TIGHTENING SPECIFICATIONS Manual FASTENER TIGHTENING SPECIFICATIONS |
||
| Axle Nut/Hub Nut | |||
| Front & Rear | 151 ft. lbs. (205 N.m) | ||
| Battery | NA | ||
| Brakes | |||
| Bleeding Sequence | RR-LF-LR-RF See HYDRAULIC BRAKE SYSTEM BLEEDING (PRESSURE) HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) |
||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Charging | |||
| Generator | NA | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Serpentine drive belts are not adjustable | ||
| Drive Belt Routing | 2.4L See illustration under INSTALLATION PROCEDURE 3.5L See illustration under INSTALLATION PROCEDURE 3.6L See illustration under INSTALLATION PROCEDURE |
||
| Engine Cooling | |||
| General Service Specifications | NA | ||
| Radiator Cap Pressure | Specification is stamped on pressure cap | ||
| Thermostat R & I | |||
| 2.4L | ENGINE COOLANT THERMOSTAT HOUSING REPLACEMENT (LE5) | ||
| 3.5L | ENGINE COOLANT THERMOSTAT REPLACEMENT (LZ4) | ||
| 3.6L | ENGINE COOLANT THERMOSTAT HOUSING REPLACEMENT (LY7) | ||
| Water Pump R & I | |||
| 2.4L | WATER PUMP REPLACEMENT (L4) | ||
| 3.5L | WATER PUMP REPLACEMENT (LZ4) | ||
| 3.6L | WATER PUMP REPLACEMENT (LY7) | ||
| Engine Mechanical | |||
| 2.4L | |||
| Compression | No cylinder should read less than 100 psi (690 kPa) Compression in any 1 cylinder should not be less than 70 percent of the highest cylinder See ENGINE COMPRESSION TEST |
||
| Oil Pressure Minimum - @1000 RPM @ 90°C (194°F) |
30-70 psi (206.84-482.63 kPa) | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS (LE5, LE9) | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| 3.5L | |||
| Compression | No cylinder should read less than 100 psi (690 kPa) Compression in any 1 cylinder should not be less than 70 percent of the highest cylinder See ENGINE COMPRESSION TEST |
||
| Oil Pressure | @ 1850 RPM 30-45 PSI (207-310 kPa) | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| 3.6L | |||
| Compression | No cylinder reading should be less than 140 psi (965 kPa) The lowest reading should not be less than 70 percent of the highest reading See ENGINE COMPRESSION TEST |
||
| Oil pressure | Minimum @ Idle 10 psi (69 kPa) Minimum @ 2,000 RPM 30 psi (207 kPa) |
||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS (LY7) | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive PlateTorque | |||
| 2.4L | A/T & M/T First Pass 39 ft. lbs. (53 N.m) Final Pass Plus an additional 25 Degrees |
||
| 3.5L | A/T 52 ft. lbs. (70 N.m) M/T First Pass 37 ft. lbs. (50 N.m) M/T Final Pass Plus an additional 70 Degrees |
||
| 3.6L | First Pass 22 ft. lbs. (30 N.m) Final Pass Plus an additional 45 Degrees |
||
| Fuel System | |||
| Pressure Specification | 2.4L & 3.6L (LCS) 50-60 psi (345-414 kPa) 3.5L & 3.6L (LY7) 56-62 psi (384-425) |
||
| Fuel Pressure Test Procedure | 2.4L CIRCUIT/SYSTEM VERIFICATION 3.5L CIRCUIT/SYSTEM VERIFICATION 3.6L CIRCUIT/SYSTEM VERIFICATION |
||
| Fuel Filter Location | 2.4L fuel filter is located in the primary fuel tank module 3.5L fuel filter is located in the primary fuel tank module 3.6L fuel filter is located in the primary fuel tank module |
||
| Fuel Filter R & I | 2.4L FUEL TANK FUEL PUMP MODULE REPLACEMENT 3.5L FUEL TANK FUEL PUMP MODULE REPLACEMENT 3.6L FUEL TANK FUEL PUMP MODULE REPLACEMENT |
||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| All Models | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | 2.4L & 3.6L Coil On Plug 3.5L 1236 ohms per ft (4,044 ohms per meter) |
||
| Ignition Wires (Routing) | |||
| 2.5L | Coil On Plug | ||
| 3.5L | See illustrations under SPARK PLUG WIRE REPLACEMENT | ||
| 3.6L | Coil On Plug | ||
| Spark Plug | |||
| 2.4L (See Catalog for application) | |||
| Gap | 0.037-0.043 in (1.1-0.95 mm) | ||
| Torque | 15 ft. lbs. (20 N.m) | ||
| 3.5L (See Catalog for application) | |||
| Gap | 0.040 in (1.02 mm) | ||
| Torque | 11 ft. lbs. (15 N.m) | ||
| 3.6L (See Catalog for application) | |||
| Gap | 0.0433 in (1.10 mm) | ||
| Torque | 13 ft. lbs. (18 N.m) | ||
| Starting | |||
| Starter | NA | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 100 ft. lbs. (140 N.m) For tightening sequence, See illustration under INSTALLATION PROCEDURE | ||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.