Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSSATURN2009ASTRA XR, 4D HATCHBACK, AUTOMATICREPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSCOMMON SPECS & PROCEDURESSPECIFICATIONS INDEX
2009 Saturn Astra XR, 4D Hatchback, Automatic
Specifications Index
2009 Saturn Astra XR, 4D Hatchback, AutomaticSECTION Specifications Index
ASTRA SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM CAPACITIES | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | Step 1 = 111 Ft. Lb. (150 N.m) Step 2 = Loosen 45 degrees Step 3 = 185 Ft. Lb. (250 N.m) |
||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | RR, LF, LR, RF HYDRAULIC BRAKE SYSTEM BLEEDING | ||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Serpentine drive belts are not adjustable | ||
| Drive Belt Routing | NA | ||
| Engine Cooling | |||
| General Service Specifications | NA | ||
| Radiator Cap Pressure | Specification is stamped on pressure cap | ||
| Thermostat R & I | ENGINE COOLANT THERMOSTAT REPLACEMENT Link | ||
| Water Pump R & I | WATER PUMP REPLACEMENT | ||
| Engine Mechanical | |||
| Compression | 14 psi maximum pressure difference ENGINE COMPRESSION TEST | ||
| Oil Pressure | Minimum Pressure at 1000 RPM 50-80 psi (344.75-551.60 kPa) | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque (NEW Bolts) | 26 lb ft + 30° + 15° (35 N.m + 30° + 15°) | ||
| Fuel System | |||
| Pressure Specification | 50-60 psi (345-414 kPa) | ||
| Fuel Pressure Test Procedure | CIRCUIT/SYSTEM TESTING | ||
| Fuel Filter Location | Plastic Fuel Strainer is Part of Fuel Pump Module in Fuel tank | ||
| Fuel Filter R & I | FUEL TANK FUEL PUMP MODULE REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | 1-3-4-2 Number 1 Cylinder Is At Front Of Engine | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug | |||
| 1.6L & 1.8L (Type NA) | |||
| Gap | 0.035-0.030 in (0.9-0.75 mm) | ||
| Torque | 12.5-17 lb ft (17-23 N.m ) | ||
| Starting | |||
| Starter | NA (non-repairable) | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 81 ft. lb. (110 N.m) | ||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.