Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Information On Drilling High Strength Steel Related To Collision Repair (10-08-98-002A)
Reference number: 10-08-98-002A
Supersedes refnos: 10-08-98-002
INFORMATION ON DRILLING HIGH STRENGTH STEEL RELATED TO COLLISION REPAIR
TECHNICAL SERVICE BULLETIN
| AFFECTED MODEL(S): | 2015 and Prior GM Passenger Cars and Light Duty Trucks |
| SUPERCEDES: | This Bulletin has been revised to add 2012-2015 Model Years. Please discard Corporate Bulletin Number 10-08-98-002. |
SERVICE INFORMATION
To improve safety, fuel economy and vehicle performance, a number of high strength steels are used in manufacturing General Motors vehicles. These various high strength steels and their location in specific vehicles can be found in Service Information | Body Repair | Collision Repair | Visual Identification.
To perform structural or collision damage repairs, it is often necessary to drill out (remove) resistance spot welds in order to separate the components being serviced from the vehicle structure.
A variety of drill bits are available to remove these resistance spot welds, however the useful life of many of these drills is limited by the hardness of the high strength steels.
The General Motors Collision Repair Technology Center has recently validated a *CryoCobalt™ drill bit that has been developed for use with very hard metals. These drill bits performed with exceptional results and should allow for increased production and reduced overall cost related to resistance spot weld removal. These drill bits can also be re-sharpened.
These drill bits are available directly from the manufacturer. Refer to the ordering information below.
*We believe this source and their products to be reliable. There may be additional manufacturers of such products/materials. General Motors does not endorse, indicate any preference for, or assume any responsibility for the products or material from this firm or for any such items that may be available from other sources.
ORDERING INFORMATION
Use the part numbers listed below for special GM pricing.
| Order Code# | Description | Size |
|---|---|---|
| GM801-4-1664 | CryoCobalt Drill Bit (min.6) | 1/4" |
| GM801-4-1665 | CryoCobalt Drill Bit (min.48) | 1/4" |
| GM801-4-2064 | CryoCobalt Drill Bit (min.6) | 5/16" |
| GM801-4-2065 | CryoCobalt Drill Bit (min.48) | 5/16" |
| GM801-4-2464 | CryoCobalt Drill Bit (min.6) | 3/8" |
| GM801-4-2465 | CryoCobalt Drill Bit (min.48) | 3/8" |
| GM999-9-4029 | CryoCobalt Drill Bit-Index 1/16" to 1/2" | N/A |
Contact the drill bit manufacturer, Partsmaster, at:
Customer Service: 972-438-0523, 7am - 5:30pm CT (E-mail: csdparts@partsmaster.com)
Technical Service: 972-438-0162, 8am - 5pm CT (E-mail: technicalservice@partsmaster.com)
NO RELATED
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.