Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSPONTIAC2006G6 GTP, 2D COUPE, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT VARIANT/TRIMSECTION 7 (ENGINE CONTROL SYSTEM - 2.4L - INTRODUCTION (2 OF 2))COMPONENT LOCATORENGINE CONTROLS COMPONENT VIEWS
2006 Pontiac G6 GTP, 2D Coupe, Standard
Engine Controls Component Views
2006 Pontiac G6 GTP, 2D Coupe, StandardSECTION Engine Controls Component Views
WARNING: This page is about a different variant/trim than selected.
| Callout | Component Name |
|---|---|
| 1 | Coolant Level Switch |
| 2 | Battery |
| 3 | Electronic Brake Control Module (EBCM) |
| 4 | C101 |
| 5 | G103 |
| 6 | Fuse Block - Underhood |
| 7 | Engine Control Module (ECM) |
| 8 | Engine Control Module (ECM) C3 |
| 9 | Engine Control Module (ECM) C2 |
| 10 | Engine Control Module (ECM) C1 |
| Callout | Component Name |
|---|---|
| 1 | Fuel Injector 1 |
| 2 | Fuel Injector 2 |
| 3 | Fuel Injector 3 |
| 4 | Manifold Absolute Pressure (MAP) Sensor |
| 5 | Fuel Injector 4 |
| 6 | Evaporative Emission (EVAP) Canister Purge Solenoid Valve |
| 7 | Camshaft Position (CMP) Sensor - Intake |
| 8 | Knock Sensor (KS) |
| 9 | Engine Oil Pressure (EOP) Switch |
| 10 | Crankshaft Position (CKP) Sensor |
| 11 | Starter Solenoid |
| 12 | Starter |
| 13 | Intake Manifold |
| Callout | Component Name |
|---|---|
| 1 | Evaporative Emission (EVAP) Canister Purge Solenoid Valve |
| 2 | Camshaft Position (CMP) Sensor - Exhaust |
| 3 | Heated Oxygen Sensor (HO2S) 1 |
| 4 | Heated Oxygen Sensor (HO2S) 2 |
| 5 | Starter |
| 6 | Engine Coolant Temperature (ECT) Sensor |
| 7 | Camshaft Position (CMP) Sensor - Intake |
| Callout | Component Name |
|---|---|
| 1 | Brake Pedal Position Sensor |
| 2 | Accelerator Pedal Position (APP) Sensor |
| 3 | Accelerator Pedal |
| 4 | Brake Pedal |
| Callout | Component Name |
|---|---|
| 1 | Heated Oxygen Sensor (HO2S) Bank 1 Sensor 2 |
| 2 | Heated Oxygen Sensor (HO2S) Bank 2 Sensor 2 |
| Callout | Component Name |
|---|---|
| 1 | Evaporative Emission (EVAP) Canister |
| 2 | Evaporative Emission (EVAP) Canister Vent Solenoid Valve |
| 3 | Fuel Tank Filler Neck |
| Callout | Component Name |
|---|---|
| 1 | Fuel Tank Pressure (FTP) Sensor, Connector |
| 2 | Fuel Pump and Sender Assembly |
| 3 | Fuel Pump and Sender Assembly Connector |
| 4 | Fuel Tank |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.