Diversity Antenna System

2006 Pontiac G6 GTP, 2D Coupe, StandardSECTION Diversity Antenna System
WARNING: This page is about a different car, the 2007 Buick Lucerne. However, it is still accessible from the selected car via links, so may be relevant.

This diversity antenna system is comprised of 3 antenna grid patterns interfacing with the rear defog grid, a radio antenna module, a coax, and a 14-volt power feed from the radio to the antenna module.

In AM and WX mode, the system functions as follows:

The antenna module takes the signal from only the AM/FM1 antenna pattern on the rear window. The antenna module amplifies this signal and sends it to the radio. In this mode the radio does not supply any voltage to the center conductor of the coax and there is no feedback signal present on the coax.

In FM mode the system functions as follows:

The antenna module takes the best signal from 1 of the 3 FM antenna patterns on the rear window. The antenna module amplifies this signal and sends it to the radio. In this mode, the radio supplies 12 volts to the center conductor of the coax and this switches the module into FM mode. The radio also supplies a feedback signal, along the coax, to the AM/FM antenna module, which indicates the quality of the signal. Based on the measured input signal level and the feedback from the radio, the antenna module switches between the 3 antennas to find the best signal.

The following information lists the most probable cause of the concern to the least probable cause, followed by the appropriate test for that condition. If the test leads to the replacement of a component, always inspect for a poor connection before proceeding with the replacement. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Perform the Antenna System Test and test the antenna coax cable prior to performing any of the following tests.

Poor Reception on Both AM and FM Bands

  • The radio antenna module is not grounded properly. The module grounding screws should be clean and tight. The antenna module ground is either a chassis ground or a ground strap. Measure the resistance from the antenna module base plate to a good ground. Resistance should be 0.20 ohms or less. Find and correct the condition if the resistance is out of specification.
  • The antenna 14-volt switch supply voltage circuit to the radio antenna module is open or shorted to ground. Test the antenna 14-volt switch supply voltage circuit for an open or short to ground. Refer to Circuit Testing and Wiring Repairs .
  • Defective antenna module-Replace the antenna module. Refer to Radio Antenna Module ReplacementΒ  for service procedure.
  • Defective antenna grid-Refer to Rear Window Replacement .

Poor Reception on AM Band Only

  • The antenna 14-volt switch supply voltage circuit to the radio antenna module is open or shorted to ground. Test the antenna 14-volt switch supply voltage circuit for an open or short to ground. Refer to Circuit Testing and Wiring Repairs .
  • Defective antenna module-Replace the antenna module. Refer to Radio Antenna Module ReplacementΒ  for service procedure.
  • Defective antenna grid-Refer to Rear Window Replacement .

Poor Reception on FM Band Only

  • The Antenna 14-volt switch supply voltage circuit to the radio antenna module is open or shorted to ground. Test the antenna 14-volt switch supply voltage circuit for an open or short to ground. Refer to Circuit Testing and Wiring Repairs .
  • Defective antenna module-Replace the antenna module. Refer to Radio Antenna Module ReplacementΒ  for service procedure.
  • Defective antenna grid-Refer to Rear Window Replacement .
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.