Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSPONTIAC2006G6 GTP, 2D COUPE, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 756 (KEYLESS ENTRY SYSTEM AND REMOTE FUNCTIONS)DIAGNOSTIC INFORMATION AND PROCEDURESSCAN TOOL DATA LIST
2006 Pontiac G6 GTP, 2D Coupe, Standard
Scan Tool Data List
2006 Pontiac G6 GTP, 2D Coupe, StandardSECTION Scan Tool Data List
WARNING: This page is about a different car, the 2007 Saturn Sky. However, it is still accessible from the selected car via links, so may be relevant.
Body Control Module (BCM)
| Scan Tool Parameter | Data List | Units Displayed | Typical Data Value |
|---|---|---|---|
| Operating Conditions: Ignition ON, Engine OFF. | |||
| Door Ajar Switch | Keyless Data | Door Closed/Door Ajar | Door Closed |
| Door Lock Switch | Keyless Data | Volts | Varies |
| Door Lock Switch | Keyless Data | Lock/Unlock/Idle | Unlock |
| Driver Door Ajar Sw. | Keyless Data | Door Closed/Door Ajar | Door Closed |
| Driver Door Lock Acutator Command | Keyless Data | Lock/Unlock/Idle/Invalid | Unlock |
| Passenger Doors Lock Actuator Command | Keyless Data | Lock/Unlock/Idle/Invalid | Unlock |
| Trunk Ajar Switch | Keyless Data | Trunk Closed/Trunk Ajar | Trunk Closed |
| Trunk Motor | Keyless Data | Off/On | Off |
| Trunk Release Solenoid Command | Keyless Data | Off/On | Off |
| Trunk Release Switch | Keyless Data | Inactive/Active | Inactive |
Remote Control Door Lock Receiver (RCDLR)
| Scan Tool Parameter | Data List | Units Displayed | Typical Data Value |
|---|---|---|---|
| Operating Conditions: Ignition ON, Engine OFF. | |||
| Fob 1 Programmed | Key FOB Information | Yes/No | Varies |
| Fob 1 Function | Key FOB Information | None/Lock/Dr Door Unlock/All Door Unlock/R Closure Rel./Lt Sliding Ctrl/Rt Sliding Ctrl/Panic/Fuel Door/Power Window/Power Top/Engine Start/Engine Stop/Fob Program/Locate/R Closure Close/R Closure Open/Double Lock/R Closure Stop/R Closure Start/Lt Sliding Stop | Varies |
| Fob 1 Battery | Key FOB Information | OK/Low | OK |
| Fob 2 Programmed | Key FOB Information | Yes/No | Varies |
| Fob 2 Function | Key FOB Information | None/Lock/Dr Door Unlock/All Door Unlock/R Closure Rel./Lt Sliding Ctrl/Rt Sliding Ctrl/Panic/Fuel Door/Power Window/Power Top/Engine Start/Engine Stop/Fob Program/Locate/R Closure Close/R Closure Open/Double Lock/R Closure Stop/R Closure Start/Lt Sliding Stop | Varies |
| Fob 2 Battery | Key FOB Information | OK/Low | OK |
| Fob 3 Programmed | Key FOB Information | Yes/No | Varies |
| Fob 3 Function | Key FOB Information | None/Lock/Dr Door Unlock/All Door Unlock/R Closure Rel./Lt Sliding Ctrl/Rt Sliding Ctrl/Panic/Fuel Door/Power Window/Power Top/Engine Start/Engine Stop/Fob Program/Locate/R Closure Close/R Closure Open/Double Lock/R Closure Stop/R Closure Start/Lt Sliding Stop | Varies |
| Fob 3 Battery | Key FOB Information | OK/Low | OK |
| Fob 4 Programmed | Key FOB Information | Yes/No | Varies |
| Fob 4 Function | Key FOB Information | None/Lock/Dr Door Unlock/All Door Unlock/R Closure Rel./Lt Sliding Ctrl/Rt Sliding Ctrl/Panic/Fuel Door/Power Window/Power Top/Engine Start/Engine Stop/Fob Program/Locate/R Closure Close/R Closure Open/Double Lock/R Closure Stop/R Closure Start/Lt Sliding Stop | Varies |
| Fob 4 Battery | Key FOB Information | OK/Low | OK |
| Last Fob Used | Key FOB Information | None/ Fob 1/ Fob 2/ Fob 3/ Fob 4/ Fob 5 | Varies |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.