SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSPONTIAC2006G6 GTP, 2D COUPE, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 654 (BATTERY, CHARGING SYSTEM AND STARTING SYSTEM)COMPONENT LOCATORENGINE ELECTRICAL COMPONENT VIEWS
2006 Pontiac G6 GTP, 2D Coupe, Standard

Engine Electrical Component Views

2006 Pontiac G6 GTP, 2D Coupe, StandardSECTION Engine Electrical Component Views
WARNING: This page is about a different car, the 2007 Chevrolet Malibu. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Starter Component Views
GM1370250Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 Battery Positive Terminal at Starter Solenoid
2 Fusible Link
3 Starter Solenoid
4 S Terminal
5 Starter
Fig 2: Lower Left Front of Engine - LX9
GM1265648Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 Engine Oil Pressure (EOP) Switch
2 Starter
3 Starter Solenoid
4 Knock Sensor (KS) 2
Fig 3: Front of the Engine (LZ9)
GM1555583Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 Intake Manifold Tuning (IMT) Valve Solenoid
2 Evaporative Emission (EVAP) Canister Purge Solenoid Valve
3 Throttle Actuator Control (TAC) Module
4 Heated Oxygen Sensor (HO2S) Bank 1 Sensor 1
5 Knock Sensor (KS) 2
6 Starter Solenoid
7 Starter
8 Engine Oil Pressure (EOP) Sensor
9 Camshaft Position (CMP) Actuator Solenoid
10 Camshaft Position (CMP) Sensor
Fig 4: View Of Right Lower Front of Engine - L61
GM1265624Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 Starter
2 Starter Solenoid
Fig 5: View Of Top Rear of Engine - LX9
GM1265688Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 Manifold Absolute Pressure (MAP) Sensor
2 Generator
3 Heated Oxygen Sensor (HO2S) Bank 1 Sensor 1
4 Ignition Control Module (ICM)
5 Exhaust Gas Recirculation (EGR) Valve
6 Evaporative Emission (EVAP) Canister Purge Solenoid
7 Throttle Actuator Control (TAC) Module
Fig 6: Top of the Engine - LZ9
GM1732562Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 Generator
Fig 7: Power and Grounding Component Views - Top Right Front of Engine - L61
GM1263982Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 G106
2 Generator
Fig 8: Power and Grounding Component Views - Left Rear of Engine Compartment
GM1264030Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 Coolant Level Switch
2 Battery
3 Electronic Brake Control Module (EBCM) (JL9/J67)
4 C101 (JL9/J67)
5 G103 (NV7)
6 Fuse Block - Underhood
7 Powertrain Control Module (PCM) (LX9/L61)/Engine Control Module (ECM)(LZ9)
8 Powertrain Control Module (PCM) C3 (LX9/L61)/Engine Control Module (ECM) C3 (LZ9)
9 Powertrain Control Module (PCM) C2 (LX9/L61)/Engine Control Module (ECM) C2 (LZ9)
10 Powertrain Control Module (PCM) C1 (LX9/L61)/Engine Control Module (ECM) C1 (LZ9)
Fig 9: Instrument Panel Component Views
GM1360206Courtesy of GENERAL MOTORS CORP.
Callout Component Name
1 Turn Signal/Multifunction Switch
2 Steering Wheel Controls - Left
3 Instrument Panel Cluster (IPC)
4 Steering Wheel Controls - Right
5 Windshield Wiper/Washer Switch
6 Ignition Switch
7 Hazard Switch
8 Ambient Light Sensor (C60), Sunload Sensor (C68)
9 Radio
10 HVAC Control Module
11 Inflatable Restraint I/P Module
12 Traction Control Switch (NW7/NW9), Auxiliary Power Outlet - Front (w/o NW7/NW9)
13 Transmission Shifter
14 Cigar Lighter
15 Horn Buttons/Inflatable Restraint Steering Wheel Module
16 Data Link Connector (DLC)
17 Fog Lamp Switch (T96)
18 Dimmer Switch
19 Adjustable Pedals Position Switch (JF4)
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.