Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSPONTIAC2006G6 GTP, 2D COUPE, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 653 (DATA COMMUNICATION SYSTEM)COMPONENT LOCATORDATA COMMUNICATION CONNECTORSBODY CONTROL MODULE (BCM) - C1 CONNECTOR
2006 Pontiac G6 GTP, 2D Coupe, Standard
Body Control Module (BCM) - C1 Connector
2006 Pontiac G6 GTP, 2D Coupe, StandardSECTION Body Control Module (BCM) - C1 Connector
WARNING: This page is about a different car, the 2007 Chevrolet Malibu. However, it is still accessible from the selected car via links, so may be relevant.
Body Control Module (BCM) - C1 Connector Parts Information
Connector Part Information
|
Terminal Part Information
|
Body Control Module (BCM) - C1 Connector Terminal Identification
| Pin | Wire Color | Circuit No. | Function |
|---|---|---|---|
| 1 | - | - | Not Used |
| 2 | L-GN/BK | 592 | DRL Relay Control |
| 3 | D-GN/WH | 636 | Ambient Air Temperature Sensor Signal |
| 4 | TN | 305 | Trunk Key Switch Signal (Sedan) |
| WH/BK | 1221 | Lift Gate Release Switch Signal (Extended Sedan) | |
| 5 | - | - | Not Used |
| 6 | YE | 61 | Ground |
| 7-11 | - | - | Not Used |
| 12 | BK | 1050 | Ground |
| 13 | TN | 28 | Horn Relay Control |
| 14 | - | - | Not Used |
| 15 | L-BU | 2182 | Reverse Lamp Relay Control |
| 16 | L-BU | 1344 | Trunk Release Relay Control |
| 17 | - | - | Not Used |
| 18 | OG/BK | 744 | Rear Compartment Lid Ajar Switch Signal |
| 19 | YE | 317 | Fog Lamp Relay Control (T96) |
| 20-21 | - | - | Not Used |
| 22 | D-GN | 113 | Windshield Wiper Switch Signal 2 |
| 23 | - | - | Not Used |
| 24 | WH | 17 | Stop Lamp Supply Voltage |
| 25 | - | - | Not Used |
| 26 | YE | 196 | Windshield Wiper Motor Park Switch Signal |
| 27-28 | - | - | Not Used |
| 29 | TN/WH | 1969 | Headlamp High Beam Relay Control |
| 30-32 | - | - | Not Used |
| 33 | BN/WH | 1571 | Traction Control Switch Signal (NW7/NW9) |
| 34 | - | - | Not Used |
| 35 | L-GN | 262 | Driver Door Key Switch Signal |
| 36 | - | - | Not Used |
| 37 | D-GN | 5060 | Low Speed GMLAN Serial Data |
| 38 | D-BU | 5364 | Left DRL/Turn Supply Voltage |
| 39 | - | - | Not Used |
| 40 | D-GN/WH | 1135 | A/T Shift Lock Control Solenoid Supply Voltage |
| 41 | - | - | Not Used |
| 42 | WH | 17 | Stop Lamp Supply Voltage |
| 43-46 | - | - | Not Used |
| 47 | L-GN | 1748 | Coolant Level Switch Signal |
| 48-50 | - | - | Not Used |
| 51 | GY/BK | 745 | Left Front Door Ajar Switch Signal |
| 52 | - | - | Not Used |
| 53 | L-GN/BK | 748 | Passenger Door Ajar Switch Signal |
| 54 | L-BU/BK | 747 | Passenger Door Ajar Switch Signal |
| 55 | D-GN | 5060 | Low Speed GMLAN Serial Data |
| 56 | D-GN | 5365 | Right DRL/Turn Supply Voltage |
| 57 | WH | 193 | Rear Defog Relay Control |
| 58 | YE | 5199 | Run/Crank Relay Coil Control |
| 59 | L-BU | 1134 | Park Brake Switch Signal |
| 60 | PK | 849 | Brake Fluid Level Sensor Signal |
| 61 | D-GN | 5525 | Tap Up/Tap Down Enable Signal |
| 62 | TN/WH | 99 | Hazard Indicator Supply Voltage |
| 63-64 | - | - | Not Used |
| 65 | WH | 1080 | Park Lamp Relay Control |
| 66 | WH | 682 | Door Lock Lock/Unlock Signal |
| 67 | WH | 682 | Door Lock Lock/Unlock Signal |
| 68 | - | - | Not Used |
| 69 | PK/BK | 109 | Hood Ajar Switch Signal (AP3/AP8) |
| 70 | PU | 5531 | Hood Ajar Switch Signal (AP3/AP8) |
| 71 | BN/WH | 2091 | Trunk Release Switch Supply Voltage |
| 72 | TN/WH | 746 | Passenger Door Ajar Switch Signal |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.