Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Scan Tool Data List
The SIR scan tool data list and PPS scan tool data list contain the restraint system related parameters that are available on the scan tool. The column, Data List, indicates the location of the parameter within the scan tool menu selections.
Use the SIR scan tool data list as directed by a diagnostic table or in order to supplement the diagnostic procedures. Begin all of the diagnostic procedures with the Diagnostic System Check - Vehicle . Use the Scan Tool Data Lists after the following is determined:
- A diagnostic directs the use of the Data List.
- There is no published diagnostic trouble code (DTC) procedure nor published symptom procedure for the customer concern.
- The DTC or symptom diagnostic procedure indicated by the diagnostic system check does not resolve the customer concern.
The typical data values are obtained from a properly operating vehicle under the conditions specified in the second row of the scan tool data list table. Comparison of the parameter values from the suspect vehicle with the typical data values may reveal the source of the customer concern.
| Scan Tool Parameter | Data List | Units Displayed | Typical Data Value |
|---|---|---|---|
| Operating Conditions: Ignition ON/Engine OFF/Driver Seat Belt Buckled/Passenger Seat Belt Unbuckled | |||
| Battery Voltage Signal | Data | Volts | Varies |
| Run/Crank | Data | Active/Inactive | Inactive |
| SIR Warning Indicator | Data | On/Off | Off |
| Driver Seat Belt Type | Sensor Data | Switch/Sensor | Switch |
| Psgr. Seat Belt Type | Sensor Data | Switch/Sensor | Sensor |
| Psgr. Seat Belt Sensor | Sensor Data | mA | Varies |
| Driver Seat Belt Switch | Sensor Data | Unbuckled/Buckled | Buckled |
| Passenger Seat Belt Switch | Sensor Data | Unbuckled/Buckled | Unbuckled |
| Driver Seat Position Sensor | Sensor Data | Forward/Rearward | Varies |
| Psgr. Seat Position Sensor | Sensor Data | Forward/Rearward | Varies |
| Primary Key Status | Key Identification | Unknown/Valid/Invalid | Valid |
| SDM Primary Key | Key Identification | 4-digit number | Varies |
| Received Primary Key | Key Identification | 4-digit number | Varies |
| Secondary Key Status | Key Identification | Unknown/Valid/Invalid | Valid |
| Received VIN Digits 2-5 | Key Identification | 4-digit number | Varies |
| Received VIN Digits 6-7 | Key Identification | 2-digit number | Varies |
| Scan Tool Parameter | Data List | Units Displayed | Typical Data Value |
|---|---|---|---|
| Operating Conditions: Ignition ON/Engine OFF/Driver Seat Belt Buckled/Passenger Seat Belt Unbuckled | |||
| Battery Voltage Signal | Data | Volts | Varies |
| Power Mode | Data | Off/Accessory/Run/Crank Request | Inactive |
| PPS Fault Status | Data | No Fault/Plant Mode/Fault/Mismatch | No Fault |
| SDM Enable Status | Data | Enabled/Disabled | Enabled |
| PPS Enable Status | Data | Enabled/Disabled | Disabled |
| Passenger Classification | Data | Unknown/Calibrating/Empty Seat/Small/Large/Re-Zero | Empty Seat |
| Passenger Status | Data | No Info./Valid/Invalid Class./Invalid Pos./Invalid Data/Inval. Class&Pos | Varies |
| Pressure Sensor | Data | Volts | Varies |
| Seat Belt Tension Sensor | Data | Volts | Varies |
| Primary Key Status | Key Identification | Unknown/Valid/Invalid | Valid |
| PPS Primary Key | Key Identification | 4-digit number | Varies |
| Received Primary Key | Key Identification | 4-digit number | Varies |
NO RELATED
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.