Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSPONTIAC2006G6 GTP, 2D COUPE, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1410 (BATTERY, CHARGING SYSTEM AND STARTING SYSTEM)
2006 Pontiac G6 GTP, 2D Coupe, Standard
Section 1410 (Battery, Charging System And Starting System)
2006 Pontiac G6 GTP, 2D Coupe, StandardSECTION Section 1410 (Battery, Charging System And Starting System)
WARNING: This page is about a different car, the 2012 Chevrolet Malibu. However, it is still accessible from the selected car via links, so may be relevant.
- Specifications
- Schematic Wiring Diagrams
- Diagnostic Information and Procedures
- Diagnostic Code Index
- DTC B1325, B1330, B1420, B1424, B1517, C0800, C0895, C0899, C0900, P0560, P0562, or P0563
- DTC B1516
- DTC P0615
- Diagnostic Instructions
- DTC Descriptor
- Diagnostic Fault Information
- Typical Scan Tool Data
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the DTC
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Component Testing
- Repair Instructions
- DTC P0621
- Diagnostic Instructions
- DTC Descriptor
- Diagnostic Fault Information
- Typical Scan Tool Data
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the DTC
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Repair Instructions
- DTC P0622
- Diagnostic Instructions
- DTC Descriptor
- Diagnostic Fault Information
- Typical Scan Tool Data
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the DTC
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Repair Instructions
- DTC P1668
- Symptoms - Engine Electrical
- Battery Inspection/Test
- Battery Charging
- Battery Electrical Drain/Parasitic Load Test
- Charging System Test
- Generator Noise Diagnosis
- Starter Solenoid Does Not Click
- Starter Solenoid Clicks, Engine Does Not Crank
- Engine Cranks Slowly
- Starter Noise Diagnosis
- Repair Instructions
- Battery Negative Cable Disconnection and Connection (LE5, LE9, LY7)
- Battery Current Sensor Replacement
- Battery Negative Cable Replacement (LY7)
- Battery Negative Cable Replacement (LE5/LE9)
- Battery Positive Cable Replacement (LY7)
- Battery Positive Cable Replacement (LE5/LE9)
- Battery Replacement (LE5, LE9, LY7)
- Battery Tray Replacement (LY7, and LE5)
- Battery Tray Replacement (LE5, LE9, LY7)
- Starter Replacement (LY7)
- Starter Replacement (LE5/LE9)
- Generator Replacement (LE5/LE9)
- Generator Replacement (LY7)
- Description and Operation
- Special Tools and Equipment
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.