SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSPONTIAC2006G6 GTP, 2D COUPE, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1230 (LIGHTING SYSTEM)DIAGNOSTIC INFORMATION AND PROCEDURESHEADLAMPS MALFUNCTIONCIRCUIT/SYSTEM TESTINGTURN SIGNAL/MULTIFUNCTION SWITCH MALFUNCTION
2006 Pontiac G6 GTP, 2D Coupe, Standard

Turn Signal/Multifunction Switch Malfunction

2006 Pontiac G6 GTP, 2D Coupe, StandardSECTION Turn Signal/Multifunction Switch Malfunction
WARNING: This page is about a different car, the 2010 Chevrolet Malibu. However, it is still accessible from the selected car via links, so may be relevant.
  1. Ignition OFF, disconnect the X1 and X2 harness connectors at the turn signal/multifunction switch.
  2. Ignition OFF, exterior lamps OFF, test for less than 5 Ξ© between the ground circuit terminal 1 and ground.
    • If greater than the specified range, test the ground circuit for an open/high resistance.
  3. Ignition OFF, exterior lamps OFF, test for less than 5 Ξ© between the ground circuit terminal B and ground.
    • If greater than the specified range, test the ground circuit for an open/high resistance.
  4. Ignition ON, verify the scan tool Headlamp On Switch parameter is Inactive.
    • If not the specified value, test the signal circuit terminal 2 for short to ground. If the circuit tests normal, replace the BCM.
  5. Verify the scan tool Headlamp Off Switch parameter is Inactive.
    • If not the specified value, test the signal circuit terminal 4 for short to ground. If the circuit tests normal, replace the BCM.
  6. Verify the scan tool Flash to Pass Switch parameter is Inactive.
    • If not the specified value, test the signal circuit terminal C for a short to ground. If the circuit tests normal, replace the BCM.
  7. Verify the scan tool High Beam Select Switch parameter is Inactive.
    • If not the specified value, test the signal circuit terminal D for a short to ground. If the circuit tests normal, replace the BCM.
  8. Install a 3 A fused jumper wire between the signal circuit terminal 2 and ground. Verify the scan tool Headlamp On Switch parameter is Active.
    • If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM.
  9. Install a 3 A fused jumper wire between the signal circuit terminal 4 and ground. Verify the scan tool Headlamp Off Switch parameter is Active.
    • If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM.
  10. Install a 3 A fused jumper wire between the signal circuit terminal C and ground. Verify the scan tool Flash to Pass Switch parameter is Active.
    • If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM.
  11. Install a 3 A fused jumper wire between the signal circuit terminal D and ground. Verify the scan tool High Beam Select Switch parameter is Active.
    • If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM.
  12. Install a 3 A fused jumper wire between the signal circuit terminal D and the control circuit terminal F. Low beam headlamps ON, verify the scan tool High Beam Select Switch parameter is Active.
    • If not the specified value, test the control circuit terminal F for an open/high resistance.
  13. If all circuits test normal, test or replace the turn signal/multifunction switch.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.