Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DBβ LIVE
HOMESERVICE MANUALSPONTIAC2006G6 GTP, 2D COUPE, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 11 (ENGINE CONTROLS - INTRODUCTION)COMPONENT LOCATORENGINE CONTROLS CONNECTOR END VIEWS
2006 Pontiac G6 GTP, 2D Coupe, Standard
Engine Controls Connector End Views
2006 Pontiac G6 GTP, 2D Coupe, StandardSECTION Engine Controls Connector End Views
WARNING: This page is about a different car, the 2005 Saturn L300. However, it is still accessible from the selected car via links, so may be relevant.
Accelerator Pedal Position (APP) Sensors
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| 1 | YE | 1274 | 5-Volt Reference |
| 2 | BN | 1164 | 5-Volt Reference |
| 3 | GY | 1161 | APP Sensor 1 Signal |
| 4 | PK | 1271 | Low Reference |
| 5 | GN | 2759 | Low Reference |
| 6 | WH | 1162 | APP Sensor 2 Signal |
Camshaft Position (CMP) Sensor
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| 1 | PU/WH | 652 | Low Reference |
| 2 | BN/WH | 633 | CMP Sensor Signal |
| 3 | GY | 416 | 5-Volt Reference A |
Crankshaft Position (CKP) Sensor
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| 1 | PU | 574 | Low Reference |
| 2 | YE | 573 | CKP Sensor Signal |
| 3 | BK/WH | 451 | Ground |
Evaporative Emissions (EVAP) Canister Purge Solenoid
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| 1 | OG | 2440 | Battery Positive Voltage |
| 2 | D-GN/WH | 428 | EVAP Canister Purge Solenoid Control |
Evaporative Emissions (EVAP) Canister Vent Solenoid
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | OG | 2740 | Ignition 1 Voltage |
| B | WH | 1310 | EVAP Canister Vent Solenoid Control |
Fuel Injectors
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| 1 | RD/BU | 2640 | Ignition 1 Voltage |
| 2 | BN/YE | 1744 | Fuel Injector 1 Control (Injector 1) |
| BN/L-GN | 1745 | Fuel Injector 2 Control (Injector 2) | |
| BN/BU | 1746 | Fuel Injector 3 Control (Injector 3) | |
| BN/RD | 844 | Fuel Injector 4 Control (Injector 4) | |
| BN/BK | 845 | Fuel Injector 5 Control (Injector 5) | |
| BN/PU | 846 | Fuel Injector 6 Control (Injector 6) | |
Fuel Pump and Sender Assembly
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | PU | 30 | Fuel Level Sensor Signal |
| B | GY | 120 | Fuel Pump Supply Voltage |
| C | BK | 650 | Ground |
| D | BK | 2759 | Low Reference |
Fuel Tank Pressure (FTP) Sensor
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| 1 | GY | 2709 | 5-Volt Reference A |
| 2 | BK | 2759 | Low Reference |
| 3 | D-GN | 890 | Fuel Tank Pressure Sensor Signal |
Heated Oxygen Sensor (HO2S) Bank 1 Sensor 1
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| 1 | PU/WH | 1665 | HO2S Input Pump Current |
| 2 | PU | 412 | HO2S Reference Voltage |
| 3 | TN | 413 | HO2S Low Reference |
| 4 | BK/WH | 751 | HO2S Heater Low Control |
| 5 | OG | 2740 | Ignition 1 Voltage |
| 6 | TN | 1667 | HO2S Output Pump Current |
Heated Oxygen Sensor (HO2S) Bank 1 Sensor 2
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| 1 | OG | 2440 | Ignition 1 Voltage |
| 2 | BK/WH | 151 | HO2S Heater Low Control |
| 3 | TN/WH | 1669 | HO2S Low Signal |
| 4 | PU/WH | 1668 | HO2S High Signal |
Heated Oxygen Sensor (HO2S) Bank 2 Sensor 1
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| 1 | PU | 1666 | HO2S Input Pump Current |
| 2 | TN/WH | 1653 | HO2S Reference Voltage |
| 3 | GY | 1979 | HO2S Low Reference |
| 4 | TN/WH | 551 | HO2S Heater Low Control |
| 5 | OG | 2440 | Ignition 1 Voltage |
| 6 | TN | 1664 | HO2S Output Pump Current |
Heated Oxygen Sensor (HO2S) Bank 2 Sensor 2
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| 1 | OG | 2740 | Ignition 1 Voltage |
| 2 | BK/WH | 51 | HO2S Heater Low Control |
| 3 | GY | 1981 | HO2S High Signal |
| 4 | TN | 1671 | HO2S Low Signal |
Ignition Control Module (ICM) Bank 1
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| 1 | BK | 250 | Ground |
| 2 | PK | 1539 | Ignition 1 Voltage |
| 3 | YE | 1157 | Ignition Coil 5 Control |
| 4 | PK | 1155 | Ignition Coil 3 Control |
| 5 | L-BU | 1153 | Ignition Coil 1 Control |
| 6 | - | - | Not Used |
Ignition Control Module (ICM) Bank 2
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| 1 | BK | 250 | Ground |
| 2 | PK | 1539 | Ignition 1 Voltage |
| 3 | TN | 1158 | Ignition Coil 6 Control |
| 4 | PU | 1156 | Ignition Coil 4 Control |
| 5 | D-BU | 1154 | Ignition Coil 2 Control |
| 6 | - | - | Not Used |
Intake Manifold Runner Control Solenoid
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| 1 | L-BU | 1110 | IMRC Solenoid Control |
| 2 | OG | 2640 | Ignition 1 Voltage |
Knock Sensor (KS) 1
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| 1 | D-BU | 496 | Knock Sensor 1 Signal |
| 2 | YE/BK | 457 | Low Reference |
Knock Sensor (KS) 2
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| 1 | L-BU | 1876 | Knock Sensor 2 Signal |
| 2 | YE/BK | 452 | Low Reference |
Mass Air Flow (MAF) Sensor
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| 1 | TN | 472 | IAT Sensor Signal |
| 2 | OG | 2440 | Ignition 1 Voltage |
| 3 | PU/WH | 652 | Low Reference |
| 4 | GY | 416 | 5-Volt Reference A |
| 5 | YE | 492 | MAF Sensor Signal |
Throttle Actuator Control (TAC) Module
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| 1 | YE | 581 | TAC Motor Control 1 |
| 2 | PU/WH | 652 | Low Reference |
| 3 | PU | - | 5-Volt Reference |
| 4 | BN | 582 | TAC Motor Control 2 |
| 5 | D-GN | - | TP Sensor 2 Signal |
| 6 | YE/BK | - | TP Sensor 1 Signal |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.