Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSPONTIAC2006G6 GTP, 2D COUPE, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1068 (VEHICLE DIAGNOSTIC INFORMATION)SPECIFICATIONSVEHICLE DIRECTION ALERT ALARM WARNING MODULE SCAN TOOL INFORMATION
2006 Pontiac G6 GTP, 2D Coupe, Standard
Vehicle Direction Alert Alarm Warning Module Scan Tool Information
2006 Pontiac G6 GTP, 2D Coupe, StandardSECTION Vehicle Direction Alert Alarm Warning Module Scan Tool Information
WARNING: This page is about a different car, the 2008 Buick Lucerne. However, it is still accessible from the selected car via links, so may be relevant.
Vehicle Direction Alert Alarm Warn Module Scan Tool Parameters
| Parameter | System State | Expected Value | Definition |
|---|---|---|---|
| Operating Conditions: Ignition ON | |||
| Battery Voltage | - | Varies | The scan tool displays volts. This is the current battery voltage. |
| Calibration Status | - | Inactive | The scan tool displays Active or Inactive. Active is displayed when the VDAAW calibration is in progress. |
| Calibration Status | - | Inhibit | The scan tool displays Inhibit or OK. Inhibit is displayed when the VDAAW detects a fault in the calibration status. |
| Diagnostic Mode | - | Inhibit | The scan tool displays Inhibit or OK. Inhibit is displayed when the VDAAW detects a fault in the diagnostic mode. |
| Mode LED | - | OFF | The scan tool displays Off or On. On is displayed when the VDAAW mode LED is illuminated. |
| Mode Switch | - | Inactive | The scan tool displays Active or Inactive. This is the status of the VDAAW mode switch |
| Operating State | - | OFF | The scan tool displays Off, Disabled, Not Ready, and Ready. This is the operating state of the VDAAW module. |
| Power Mode | - | OFF | The scan tool displays Off, Run, Crank Request, and Accessory. This is the state of power for the VDAAW module. |
| Power Mode | - | Inhibit | The scan tool displays Inhibit or OK. Inhibited is displayed when VDAAW detects a fault in the power mode. |
| Reference Voltage 1 | - | Varies | The scan tool displays volts. |
| Reference Voltage 2 | - | Varies | The scan tool displays volts. |
| Serial Data | - | Inhibit | The scan tool displays Inhibit or OK. Inhibit is displayed when VDAAW detects a fault in the serial data. |
| System Operation Status | - | Unknown | The scan tool displays Unknown, Normal, Disabled, and Failed. This is the status of the VDAAW modules system operation. |
| System Power Mode | - | Inhibit | The scan tool displays Inhibit or OK. Inhibit is displayed when the VDAAW detects a fault in the system power mode. |
Vehicle Direction Alert Alarm Warn Module Scan Tool Output Controls
| Scan Tool Output Control | Description |
|---|---|
| Calibrate Module | This output control is used to calibrate the VDDAW module. |
| Direction Warning Left | This output control is used to calibrate the left sensor. |
| Direction Warning Right | This output control is used to calibrate the right sensor. |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.