Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSPONTIAC2004AZTEK AWD V6-3.4L VIN EREPAIR AND DIAGNOSISPOWERTRAIN MANAGEMENTEMISSION CONTROL SYSTEMSTECHNICAL SERVICE BULLETINSEMISSION - EMISSIONS PROGRAMMING WARRANTY COVERAGE
2004 Pontiac Aztek AWD V6-3.4L VIN E
Emission - Emissions Programming Warranty Coverage
2004 Pontiac Aztek AWD V6-3.4L VIN ESECTION Emission - Emissions Programming Warranty Coverage
WARRANTY ADMINISTRATION
Bulletin No.: 04-06-04-036E
Date: May 08, 2008
Subject:
Warranty Coverage for Emission-Related Reprogramming Events (PCM, ECM and TCM)
Models:
2009 and Prior GM Passenger Cars and Trucks (Including Saturn)
2003-2009 HUMMER H2
2006-2009 HUMMER H3
2009 and Prior Saab Vehicles (Canada Only)
Attention:
This bulletin applies only to dealers in the United States and Canada. Export dealers are not authorized to utilize this service bulletin.
Supercede:
This bulletin is being updated to add an Attention statement. Please discard Corporate Bulletin Number 04-06-04-036D (Section 06 - Engine).
The coverage for emission-related reprogramming has the same coverage as the emission controller under the emission controller warranty - 8 years/80,000 miles (130,000 km).
Reprogramming that is not emissions-related is covered under the terms of the Bumper to Bumper Limited Warranty. (For additional information regarding labor codes for use in non-emission-related reprogramming refer to Corporate Bulletin Number 06-08-47-001D.)
Emissions-related calibration updates will be announced through a GM Technical Service Bulletin with specific guidelines of coverage for each model affected. A special emission-related reprogramming labor operation will be used. The labor operation to be used for claims relating to emission-related reprogramming is J6353 and will only be referenced in the bulletins addressing emission-related calibrations. This labor operation must NOT be used for non-emissions-related reprogramming or for any other vehicle that is not referenced in an emission-related reprogramming technical service bulletin.
Example:
The PCM on 2004 model light duty vehicles is covered by the emission controller warranty for 8 years/80,000 miles (130,000 km). If GM released an "emission-related" calibration update for one of these vehicles, this reprogramming event would also be covered for the remainder of the 8 years/80,000 miles (130,000 km). If GM released a driveability-related calibration update (for example to eliminate a hesitation) for one of these vehicles, this reprogramming event would be covered for the remainder of the terms of the Bumper to Bumper Limited Warranty.
An emission-related calibration for medium duty and diesel applications are also covered by the emission warranty that is applicable to that vehicle's emissions controller.
Example:
The PCM on 2004 model medium duty vehicles is covered by the emission controller warranty for 5 years/50,000 miles (80,000 km). If GM released an "emission-related" calibration update for one of these vehicles, this reprogramming event would also be covered for 5 years/50,000 miles (80,000 km).
Disclaimer
Bulletin No.: 04-06-04-036E
Date: May 08, 2008
Subject:
Warranty Coverage for Emission-Related Reprogramming Events (PCM, ECM and TCM)
Models:
2009 and Prior GM Passenger Cars and Trucks (Including Saturn)
2003-2009 HUMMER H2
2006-2009 HUMMER H3
2009 and Prior Saab Vehicles (Canada Only)
Attention:
This bulletin applies only to dealers in the United States and Canada. Export dealers are not authorized to utilize this service bulletin.
Supercede:
This bulletin is being updated to add an Attention statement. Please discard Corporate Bulletin Number 04-06-04-036D (Section 06 - Engine).
The coverage for emission-related reprogramming has the same coverage as the emission controller under the emission controller warranty - 8 years/80,000 miles (130,000 km).
Reprogramming that is not emissions-related is covered under the terms of the Bumper to Bumper Limited Warranty. (For additional information regarding labor codes for use in non-emission-related reprogramming refer to Corporate Bulletin Number 06-08-47-001D.)
Emissions-related calibration updates will be announced through a GM Technical Service Bulletin with specific guidelines of coverage for each model affected. A special emission-related reprogramming labor operation will be used. The labor operation to be used for claims relating to emission-related reprogramming is J6353 and will only be referenced in the bulletins addressing emission-related calibrations. This labor operation must NOT be used for non-emissions-related reprogramming or for any other vehicle that is not referenced in an emission-related reprogramming technical service bulletin.
Example:
The PCM on 2004 model light duty vehicles is covered by the emission controller warranty for 8 years/80,000 miles (130,000 km). If GM released an "emission-related" calibration update for one of these vehicles, this reprogramming event would also be covered for the remainder of the 8 years/80,000 miles (130,000 km). If GM released a driveability-related calibration update (for example to eliminate a hesitation) for one of these vehicles, this reprogramming event would be covered for the remainder of the terms of the Bumper to Bumper Limited Warranty.
An emission-related calibration for medium duty and diesel applications are also covered by the emission warranty that is applicable to that vehicle's emissions controller.
Example:
The PCM on 2004 model medium duty vehicles is covered by the emission controller warranty for 5 years/50,000 miles (80,000 km). If GM released an "emission-related" calibration update for one of these vehicles, this reprogramming event would also be covered for 5 years/50,000 miles (80,000 km).
Disclaimer
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.