Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSPONTIAC2004AZTEK AWD V6-3.4L VIN EREPAIR AND DIAGNOSISINSTRUMENT PANEL, GAUGES AND WARNING INDICATORSINSTRUMENT CLUSTER / CARRIERSERVICE AND REPAIRINSTRUMENT PANEL CLUSTER (IPC) - REPLACEMENT
2004 Pontiac Aztek AWD V6-3.4L VIN E
Instrument Panel Cluster (IPC) - Replacement
2004 Pontiac Aztek AWD V6-3.4L VIN ESECTION Instrument Panel Cluster (IPC) - Replacement
INSTRUMENT PANEL CLUSTER (IPC) REPLACEMENT
REMOVAL PROCEDURE
IMPORTANT: Turn the ignition switch to the OFF position before you remove the instrument panel cluster.
1. Remove the instrument panel (I/P) cluster trim plate bezel.
2. Remove the screws from the I/P cluster.
3. Disconnect the electrical connectors from the I/P cluster.
4. Remove the I/P cluster.
5. If not equipped with ABS (JL9) brakes, perform the following additional steps:
5.1. Disconnect the battery and touch the cables together.
5.2. Remove all fuses marked ABS.
INSTALLATION PROCEDURE
1. Connect the electrical connectors to the I/P cluster.
2. Install the I/P cluster.
NOTE: Refer to Fastener Notice in Service Precautions.
3. Install the screws to the I/P cluster.
Tighten
Tighten the screws to 2 N.m (18 lb in).
4. Install the I/P cluster trim plate bezel.
5. If not equipped with ABS (JL9) brakes, perform the following additional steps:
5.1. Reconnect the battery cables.
5.2. Turn the ignition ON and allow the IPC to go through the relearn process.
5.3. Turn the ignition OFF and open the drivers door to cancel the retained accessory power.
5.4. Reinstall the ABS fuses, turn the ignition to RUN.
6. Calibrate the electronic compass.
7. Verify the repair.
REMOVAL PROCEDURE
IMPORTANT: Turn the ignition switch to the OFF position before you remove the instrument panel cluster.
1. Remove the instrument panel (I/P) cluster trim plate bezel.
2. Remove the screws from the I/P cluster.
3. Disconnect the electrical connectors from the I/P cluster.
4. Remove the I/P cluster.
5. If not equipped with ABS (JL9) brakes, perform the following additional steps:
5.1. Disconnect the battery and touch the cables together.
5.2. Remove all fuses marked ABS.
INSTALLATION PROCEDURE
1. Connect the electrical connectors to the I/P cluster.
2. Install the I/P cluster.
NOTE: Refer to Fastener Notice in Service Precautions.
3. Install the screws to the I/P cluster.
Tighten
Tighten the screws to 2 N.m (18 lb in).
4. Install the I/P cluster trim plate bezel.
5. If not equipped with ABS (JL9) brakes, perform the following additional steps:
5.1. Reconnect the battery cables.
5.2. Turn the ignition ON and allow the IPC to go through the relearn process.
5.3. Turn the ignition OFF and open the drivers door to cancel the retained accessory power.
5.4. Reinstall the ABS fuses, turn the ignition to RUN.
6. Calibrate the electronic compass.
7. Verify the repair.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.