Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSOLDSMOBILE1970TORONADO BASE, ENG CD US, NOT AVAILABLE TRANSREPAIR AND DIAGNOSIS (SINGLE PAGE)GENERAL INFORMATIONSTEERINGMAP - STEERING, SUSPENSION, WHEEL ALIGNMENT, WHEELS & TIRESSTEERING AND SUSPENSION, WHEEL ALIGNMENT, WHEELS AND TIRESDISTANCE REGULATION SENSOR
1970 Oldsmobile Toronado Base, Eng CD US, Not Available Trans
Distance Regulation Sensor
1970 Oldsmobile Toronado Base, Eng CD US, Not Available TransSECTION Distance Regulation Sensor
NOTE:
OEM may require this sensor be calibrated to the vehicle thrustline.
| Condition | Code | Procedure |
|---|---|---|
| Attaching hardware broken | A | Require repair or replacement of hardware |
| Attaching hardware corroded, affecting structural integrity | A | Require replacement of hardware |
| Attaching hardware missing | C | Require replacement of hardware |
| Attaching hardware not functioning | A | Require repair or replacement of hardware |
| Attaching hardware threads damaged | A | Require repair or replacement of hardware |
| Attaching hardware threads stripped (threads missing) | A | Require replacement of hardware |
| Connector (Weatherpack type) leaking | A | Require repair or replacement |
| Connector broken | A | Require repair or replacement |
| Connector melted | A | Require replacement |
| Connector missing | C | Require replacement |
|
NOTE:
Determine cause and correct prior to replacement of part.
|
||
| Dust boot missing | C | Require replacement of boot |
| Dust boot split | A | Require replacement of boot |
|
NOTE:
If boot is not available separately, suggest replacement of sensor (reason code 2). This condition can lead to damage of the sliding magnet, which, in turn, causes premature sensor failure
|
||
| Dust boot torn | A | Require replacement of boot |
|
NOTE:
If boot is not available separately, suggest replacement of sensor (reason code 2). This condition can lead to damage of the sliding magnet, which, in turn, causes premature sensor failure.
|
||
| Housing cracked | B | Require replacement |
|
NOTE:
If boot is not available separately, suggest replacement of sensor (reason code 2). This condition can lead to damage of the sliding magnet, which, in turn, causes premature sensor failure.
|
||
| Lead routing incorrect | B | Require rerouting according to vehicle manufacturer's specifications |
| Loose | B | Require adjustment to vehicle manufacturer's specifications |
| Missing | C | Require replacement |
| Output signal incorrect | B | Require repair or replacement |
| Terminal burned, affecting performance | A | Require repair or replacement |
|
NOTE:
Determine cause and correct prior to repair or replacement of part.
|
||
| Terminal burned, not affecting performance | 2 | Suggest repair or replacement |
| Terminal corroded, affecting performance | A | Require repair or replacement |
| Terminal corroded, not affecting performance | 2 | Suggest repair or replacement |
| Terminal loose, affecting performance | B | Require repair or replacement |
| Terminal loose, not affecting performance | 1 | Suggest repair or replacement |
| Wire lead burned | A | Require repair or replacement |
| Wire lead conductors exposed | B | Require repair or replacement |
| Wire lead open | A | Require repair or replacement |
| Wire lead shorted | A | Require repair or replacement |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.