Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
PR25DD engine
Before Replacing ECMÂ
- SAVE ECM DATAÂ
With CONSULT
- Turn ignition switch OFF.
- Reconnect all harness connectors disconnected.
- Turn ignition switch ON.
- Select "SAVING DATA FOR REPLC CPU" in "WORK SUPPORT" mode of "ENGINE" using CONSULT.
- Follow the instruction of CONSULT display.
NOTE:- Necessary data in ECM is copied and saved to CONSULT.
- Go to Step 2 regardless of with or without success in saving data.
GO TO 2.
- SAVE 'OPERATION LOG'Â
With CONSULT
Save Operation Log, according to the procedure of "Programming" in CONSULT Operation Manual.
NOTE: ECM part number is saved in Operating Log saved in CONSULT.- Replace ECM.
- After replacing ECM, perform necessary work.
After Replacing ECMÂ
- CHECK 'OPERATION LOG'Â
With CONSULT
Check Operation Log saved before replacing ECM, according to the procedure of "Programming" in CONSULT Operation Manual.
NOTE: For the vehicle that the programming is to be performed, check if Operation Log of Vehicle Identification Number (VIN) is in Saved Data List.Is there an applicable Operation Log in the Saved Data List?
YES
GO TO 2.
NO
GO TO 3.
- PERFORM ECM PROGRAMMINGÂ
With CONSULT
Perform ECM programming, according to "Programming" of CONSULT Operation Manual. Refer to CONSULT Operation Manual.
CAUTION: During programming, maintain the following conditions:- Ignition switch: ON
- Electric load: OFF
- Brake pedal: Not depressed
- Battery voltage: 12 - 13.5 V (Check the value displayed on the CONSULT screen.)
GO TO 5.
- READ IN ECM PART NUMBER BY 'FAST LINKED'Â
Obtain ECM part number by NISSAN PARTS CATALOGUE GLOBAL Web-FAST, according to the procedure of 'FAST linked' in CONSULT Operation Manual. Refer to CONSULT Operation Manual.
NOTE: 'FAST linked' allows an appropriate programming by obtaining ECU part number from NISSAN PARTS CATALOGUE GLOBAL Web-FAST even when the part number cannot be obtained from the old ECU used before replacing with a new one.GO TO 4.
- PERFORM ECM PROGRAMMING (FAST LINKED)Â
With CONSULT
Perform ECM programming according to the procedure of FAST linked in CONSULT Operation Manual. Refer to CONSULT Operation Manual.
CAUTION: During programming, maintain the following conditions:- Ignition switch: ON
- Electric load: OFF
- Brake pedal: Not depressed
- Battery voltage: 12 - 13.5 V (Check the value displayed on the CONSULT screen.)
GO TO 5.
- PERFORM INITIALIZATION OF NATS SYSTEM AND REGISTRATION OF ALL NATS IGNITION KEY IDSÂ
Refer to Work Procedure .
GO TO 6.
- CHECK ECM DATA STATUSÂ
Check if the data is successfully copied from the ECM at Step 1 (before replacement) and saved in CONSULT.
Is the data saved successfully?
YES
GO TO 7.
NO
GO TO 8.
- WRITE ECM DATAÂ
With CONSULT
- Select "WRITING DATA FOR REPLC CPU" in "WORK SUPPORT" mode of "ENGINE" using CONSULT.
- Follow the instruction of CONSULT display.
NOTE: The data saved by "SAVING DATA FOR REPLC CPU" is written to ECM.GO TO 9.
- PERFORM VIN REGISTRATIONÂ
Refer to Work Procedure .
GO TO 9.
- PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNINGÂ
Refer to Work Procedure .
GO TO 10.
- PERFORM THROTTLE VALVE CLOSED POSITION LEARNINGÂ
Refer to Work Procedure .
GO TO 11.
- PERFORM IDLE AIR VOLUME LEARNINGÂ
Refer to Work Procedure .
GO TO 12.
- PERFORM EGR VOLUME CONTROL VALVE CLOSED POSITION LEARNINGÂ
Refer to Work Procedure .
GO TO 13.
- CHECK DTCÂ
- Turn ignition switch OFF and wait for 10 seconds or more.
- Turn ignition switch ON.
- If DTC is displayed, perform diagnosis of detected DTC. Refer to DTC Index .
END
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
