SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSNISSAN-DATSUN2016TITAN XD SL, 5.0L ENG VIN B, 4WDREPAIR AND DIAGNOSIS (SINGLE PAGE)ACCESSORIES & EQUIPMENTDRIVERS ASSISTANCE SYSTEMS - ADASAUDIO, VISUAL & NAVIGATION SYSTEM (AROUND VIEW MONITOR SYSTEM)SYSTEM DESCRIPTIONSYSTEMFAIL-SAFE
2016 Nissan-Datsun Titan XD SL, 5.0L Eng VIN B, 4WD

System Description: System: Fail-Safe

2016 Nissan-Datsun Titan XD SL, 5.0L Eng VIN B, 4WDSECTION Fail-Safe
DTC
Display Contents Of CONSULT		 Malfunction Detection Condition Fail-Safe Condition
U0428: ST ANGLE SENSOR CALIBRATION Neutral position adjustment of steering angle sensor is not complete.
  • Predicted course line is not displayed.
  • MOD (Moving Object Detection) function is stopped.
U1000: CAN COMM CIRCUIT When around view monitor control unit cannot transmit/receive CAN communication signal continuously for 2 seconds or more. The following functions are stopped
  • When communication of steering angle sensor signal is not normal:
    1. Predicted course line is not displayed.
    2. MOD (Moving Object Detection) function is stopped.
  • When communication of vehicle signal, wheel speed sensor signal, and shift signal is not normal:
    1. Predicted course line is not displayed.
    2. MOD (Moving Object Detection) function is stopped.
U111A: REAR CAMERA IMAGE SIGNAL No-signal status of rear camera image signal is continued for 500 ms or more while ignition switch is ON. Camera image is not displayed (gray screen display).
U111B: SIDE CAMERA RH IMAGE SIGNAL No-signal status of side camera RH image signal is continued for 500 ms or more while ignition switch is ON.
U111C: FRONT CAMERA IMAGE SIGNAL No-signal status of front camera image signal is continued for 500 ms or more while ignition switch is ON.
U111D: SIDE CAMERA LH IMAGE SIGNAL No-signal status of side camera LH image signal is continued for 500 ms or more while ignition switch is ON.
U1232: ST ANGLE SEN CALIB Neutral position adjustment of steering angle sensor is performed. NG signal from steering angle sensor is received.
  • Predicted course line is not displayed.
  • MOD (Moving Object Detection) function is stopped.
U1302: CAMERA POWER VOLT Camera power supply voltage does not satisfy the following conditions for 2 seconds or more when ignition switch is turned ON:
  • When supplemental lighting power supply output is ON: 5.9 - 6.5 V.
  • When OFF: 0 V by camera power supply measurement.
 Camera power output is stopped.
U1304: CAMERA IMAGE CALIB
  • When camera calibration is incomplete.
  • When camera information in around view monitor control unit and information read from camera are not the same.
 Unmatched icon UNMATCH2 display (red) is displayed (applicable for unmatched camera only).
U1305: CONFIG UNFINISH The vehicle setting of around view monitor control unit is incomplete. Operation is according to the vehicle setting value as default value.
Other When around view monitor control unit is not normal. Switch to camera screen is not allowed.
When communication between around view monitor control unit and each camera is not normal. On applicable camera screen, NO COMM marking (Red) is displayed.
When communication line between around view monitor control unit and each camera image line is affected by electromagnetic noises. On applicable camera image screen, UNMATCH2 display (Blue) is displayed.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.