SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSNISSAN-DATSUN2015ROGUE SV, AWDREPAIR AND DIAGNOSISENGINE PERFORMANCETESTING & DIAGNOSISENGINE CONTROL SYSTEM (DIAGNOSTIC TROUBLE CODES (DTCS) P014C-P0643)DTC/CIRCUIT DIAGNOSISDTC P0461: FUEL LEVEL SENSORDTC DESCRIPTIONDTC CONFIRMATION PROCEDURE
2015 Nissan-Datsun Rogue SV, AWD

DTC Confirmation Procedure

2015 Nissan-Datsun Rogue SV, AWDSECTION DTC Confirmation Procedure

  1. CHECK DTC PRIORITY

    If DTC P0461 is displayed with DTC UXXXX or P0607, first perform the trouble diagnosis for DTC UXXXX or P0607.

    Is applicable DTC detected?

    YES 

    Perform diagnosis of applicable. Refer to DTC INDEX .

    NO 

    GO TO STEP 2  .

  2. PRECONDITIONING

    WARNING:

    When performing following procedure, be sure to observe the handling of the fuel. Refer to GENERAL PRECAUTION .

    TESTING CONDITION: 

    Before starting component function check, preparation of draining fuel and refilling fuel is required. 

    Do you have CONSULT?

    YES 

    GO TO STEP 3  .

    NO 

    GO TO STEP 4  .

  3. PERFORM COMPONENT FUNCTION CHECK

    G-20 With CONSULT

    NOTE:

    Start from step 10, if it is possible to confirm that the fuel cannot be drained by 30 LITER (7-7/8 US gal, 6-5/8 Imp gal) in advance.

    1. Prepare a fuel container and a spare hose.
    2. Release fuel pressure from fuel line, refer to WORK PROCEDURE .
    3. Remove the fuel feed hose on the fuel level sensor unit.
    4. Connect a spare fuel hose where the fuel feed hose was removed.
    5. Turn ignition switch OFF and wait at least 10 seconds then turn ON.
    6. Select "FUEL LEVEL SE" in "DATA MONITOR" mode of "ENGINE" using CONSULT.
    7. Check "FUEL LEVEL SE" output voltage and note it.
    8. Select "FUEL PUMP RELAY" in "ACTIVE TEST" mode of "ENGINE" using CONSULT.
    9. Touch "ON" and drain fuel approximately 30 LITER (7-7/8 US gal, 6-5/8 Imp gal) and stop it.
    10. Check "FUEL LEVEL SE" output voltage and note it.
    11. Fill fuel into the fuel tank for 30 LITER (7-7/8 US gal, 6-5/8 Imp gal).
    12. Check "FUEL LEVEL SE" output voltage and note it.
    13. Confirm whether the voltage changes more than 0.03 V during step 7 to 10 and 10 to 12.

    Is the inspection result normal?

    YES 

    INSPECTION END

    NO 

    Proceed to DIAGNOSIS PROCEDURE .

  4. PERFORM COMPONENT FUNCTION CHECK

    G-21 Without CONSULT

    NOTE:

    Start from step 8, if it is possible to confirm that the fuel cannot be drained by 30 LITER (7-7/8 US gal, 6-5/8 Imp gal) in advance.

    1. Prepare a fuel container and a spare hose.
    2. Release fuel pressure from fuel line. Refer to WORK PROCEDURE .
    3. Remove the fuel feed hose on the fuel level sensor unit.
    4. Connect a spare fuel hose where the fuel feed hose was removed.
    5. Turn ignition switch ON.
    6. Drain fuel by 30 LITER (7-7/8 US gal, 6-5/8 Imp gal) from the fuel tank using proper equipment.
    7. Confirm that the fuel gauge indication varies.
    8. Fill fuel into the fuel tank for 30 LITER (7-7/8 US gal, 6-5/8 Imp gal).
    9. Confirm that the fuel gauge indication varies.

    Is the inspection result normal?

    YES 

    INSPECTION END

    NO 

    Proceed to DIAGNOSIS PROCEDURE .

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.