SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSNISSAN-DATSUN2015ROGUE SV, AWDREPAIR AND DIAGNOSISACCESSORIES & EQUIPMENTINFOTAINMENTAUDIO, VISUAL & NAVIGATION SYSTEM (NAVIGATION WITHOUT BOSE)DTC/CIRCUIT DIAGNOSISSTEERING SWITCHDIAGNOSIS PROCEDURE
2015 Nissan-Datsun Rogue SV, AWD

Diagnosis Procedure

2015 Nissan-Datsun Rogue SV, AWDSECTION Diagnosis Procedure

Regarding Wiring Diagram information, refer to WIRING DIAGRAM .

  1. CHECK STEERING WHEEL AUDIO CONTROL SWITCH RESISTANCE

    1. Turn ignition switch OFF.
    2. Disconnect combination switch connector M90.
    3. Check resistance between the terminals of combination switch connector M90.
    Combination switch connector M90 Condition Resistance Ω
    (Approx.)
    Terminal Terminal
    25 19 Depress SOURCE switch. 1
    Depress UTRI switch. 121
    Depress DTRI switch. 321
    Depress TELPTT switch. 723
    Depress ENTER switch. 2023
    18 Depress -SPEAKER switch. 1
    Depress SPEAKER+ switch. 121
    Depress TEL_END switch. 321
    Depress BACK_R switch. 723
    Depress DISPLAY switch. 2023

    Is the inspection result normal?

    YES 

    GO TO STEP 2  .

    NO 

    Replace steering switches. Refer to REMOVAL AND INSTALLATION .

  2. CHECK HARNESS BETWEEN COMBINATION METER AND COMBINATION SWITCH

    1. Disconnect combination meter connector M76 and combination switch connector M30.
    2. Check continuity between combination meter connector M76 and combination switch connector M30.
      Combination meter Combination switch Continuity
      Connector Terminal Connector Terminal
      M76 22 M30 8 Yes
      23 15
      21 14
    3. Check continuity between combination meter connector M76 and ground.
      Combination meter Ground Continuity
      Connector Terminal
      M76 22 - No
      23
      21

    Is the inspection result normal?

    YES 

    GO TO STEP 3  .

    NO 

    Repair or replace harness or connectors.

  3. CHECK COMBINATION SWITCH

    Check continuity between combination switch connectors M90 and M30.

    Combination switch Continuity
    Connector Terminal Connector Terminal
    M90 25 M30 8 Yes
    18 15
    19 14

    Is the inspection result normal?

    YES 

    GO TO STEP 4  .

    NO 

    Replace spiral cable. Refer to REMOVAL AND INSTALLATION .

  4. CHECK HARNESS BETWEEN COMBINATION METER AND AV CONTROL UNIT

    1. Disconnect combination meter connector M77 and AV control unit connector M102.
    2. Check continuity between combination meter connector M77 and AV control unit connector M102.
      Combination meter AV control unit Continuity
      Connector Terminal Connector Terminal
      M77 47 M102 31 Yes
      48 32
    3. Check continuity between combination meter connector M77 and ground.
      Combination meter Ground Continuity
      Connector Terminal
      M77 47 - No
      48

    Is the inspection result normal?

    YES 

    Replace AV control unit. Refer to REMOVAL AND INSTALLATION .

    NO 

    Repair or replace harness or connectors.

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.