SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSNISSAN-DATSUN2015ROGUE SV, AWDREPAIR AND DIAGNOSISACCESSORIES & EQUIPMENTINFOTAINMENTAUDIO, VISUAL & NAVIGATION SYSTEM (NAVIGATION WITH BOSE)DTC/CIRCUIT DIAGNOSISDTC U111A: REAR CAMERA IMAGE SIGNAL CIRCUITDIAGNOSIS PROCEDUREWITH DRIVER ASSISTANCE SYSTEM
2015 Nissan-Datsun Rogue SV, AWD

With Driver Assistance System

2015 Nissan-Datsun Rogue SV, AWDSECTION With Driver Assistance System

  1. CHECK REAR VIEW CAMERA POWER SUPPLY AND GROUND CIRCUIT CONTINUITY

    1. Turn ignition switch OFF.
    2. Disconnect around view monitor control unit and rear view camera connectors.
    3. Check continuity between around view monitor control unit connector M114 and rear view camera connector D514.
      Around view monitor control unit Rear view camera Continuity
      Connector Terminals Connector Terminals
      M114 50 D514 8 Yes
      52 7
    4. Check continuity between around view monitor control unit connector M114 and ground.
      Around view monitor control unit Ground Continuity
      Connector Terminal
      M114 50 No

    Is the inspection result normal?

    YES 

    GO TO STEP 2  .

    NO 

    Repair or replace harness or connectors.

  2. CHECK REAR VIEW CAMERA POWER SUPPLY VOLTAGE

    1. Connect around view monitor control unit and rear view camera connectors.
    2. Turn ignition switch ON.
    3. Check voltage between around view monitor control unit connector M114 and ground.
      Around view monitor control unit Ground Condition Voltage
      (Approx.)
      Connector Terminal
      M114 50 - CAMERA switch is ON or selector lever in R (reverse). 6.0 V

    Is the inspection result normal?

    YES 

    GO TO STEP 3  .

    NO 

    Replace around view monitor control unit. Refer to REMOVAL AND INSTALLATION .

  3. CHECK REAR VIEW CAMERA IMAGE SIGNAL AND IMAGE SIGNAL GROUND CIRCUIT CONTINUITY

    1. Turn ignition switch OFF.
    2. Disconnect around view monitor control unit and rear view camera connectors.
    3. Check continuity between around view monitor control unit connector M114 and rear view camera connector D514.
      Around view monitor control unit Rear view camera Continuity
      Connector Terminals Connector Terminals
      M114 53 D514 5 Yes
      54 1
    4. Check continuity between around view monitor control unit connector M114 and ground.
      Around view monitor control unit Ground Continuity
      Connector Terminal
      M114 53 No

    Is the inspection result normal?

    YES 

    GO TO STEP 4  .

    NO 

    Repair or replace harness or connectors.

  4. CHECK REAR VIEW CAMERA IMAGE SIGNAL

    1. Connect around view monitor control unit and rear view camera connectors.
    2. Turn ignition switch ON.
    3. Check signal between the terminals of around view monitor control unit connector M114.
      Around view monitor control unit connector M114 Condition Reference value
      (+) (-)
      Terminal Terminal
      53 54 CAMERA switch is ON or selector lever in R (reverse).
      GNSJSNIA0834GB-834Courtesy of NISSAN NORTH AMERICA, INC.

    Is the inspection result normal?

    YES 

    Replace around view monitor control unit. Refer to REMOVAL AND INSTALLATION .

    NO 

    Replace rear view camera. Refer to REMOVAL AND INSTALLATION .

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.