SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSNISSAN-DATSUN2015ROGUE SV, AWDREPAIR AND DIAGNOSIS (SINGLE PAGE)ACCESSORIES & EQUIPMENTENTERTAINMENT SYSTEMSAUDIO, VISUAL & NAVIGATION SYSTEM (NAVIGATION WITHOUT BOSE)DTC/CIRCUIT DIAGNOSISDTC U111D: SIDE CAMERA LH IMAGE SIGNAL CIRCUITDIAGNOSIS PROCEDURE
2015 Nissan-Datsun Rogue SV, AWD

Diagnosis Procedure

2015 Nissan-Datsun Rogue SV, AWDSECTION Diagnosis Procedure

Regarding Wiring Diagram information, refer to WIRING DIAGRAM .

  1. CHECK LH SIDE CAMERA POWER SUPPLY AND GROUND CIRCUIT CONTINUITY

    1. Turn ignition switch OFF.
    2. Disconnect around view monitor control unit and LH side camera connectors.
    3. Check continuity between around view monitor control unit connector M114 and LH side camera connector D14.
      Around view monitor control unit LH side camera Continuity
      Connector Terminals Connector Terminals
      M114 56 D14 7 Yes
      58 8
    4. Check continuity between around view monitor control unit connector M114 and ground.
      Around view monitor control unit Ground Continuity
      Connector Terminal
      M114 56 No

    Is the inspection result normal?

    YES 

    GO TO STEP 2  .

    NO 

    Repair or replace harness or connectors.

  2. CHECK LH SIDE CAMERA POWER SUPPLY VOLTAGE

    1. Connect around view monitor control unit and LH side camera connectors.
    2. Turn ignition switch ON.
    3. Check voltage between around view monitor control unit connector M114 and ground.
      Around view monitor control unit Ground Condition Voltage
      (Approx.)
      Connector Terminal
      M114 56 - CAMERA switch is ON or selector lever in R (reverse). 6.0 V

    Is the inspection result normal?

    YES 

    GO TO STEP 3  .

    NO 

    Replace around view monitor control unit. Refer to REMOVAL AND INSTALLATION .

  3. CHECK LH SIDE CAMERA IMAGE SIGNAL AND IMAGE SIGNAL GROUND CIRCUIT CONTINUITY

    1. Turn ignition switch OFF.
    2. Disconnect around view monitor control unit and LH side camera connectors.
    3. Check continuity between around view monitor control unit connector M114 and LH side camera connector D14.
      Around view monitor control unit LH side camera Continuity
      Connector Terminals Connector Terminals
      M114 59 D14 16 Yes
      60 15
    4. Check continuity between around view monitor control unit connector M114 and ground.
      Around view monitor control unit Ground Continuity
      Connector Terminal
      M114 59 No

    Is the inspection result normal?

    YES 

    GO TO STEP 4  .

    NO 

    Repair or replace harness or connectors.

  4. CHECK LH SIDE CAMERA IMAGE SIGNAL

    1. Connect around view monitor control unit and LH side camera connectors.
    2. Turn ignition switch ON.
    3. Check signal between the terminals of around view monitor control unit connector M114.
      Around view monitor control unit connector M114 Condition Reference value
      (+) (-)
      Terminal Terminal
      59 60 CAMERA switch is ON or selector lever in R (reverse).
      GNSJSNIA0834GB-834Courtesy of NISSAN NORTH AMERICA, INC.

    Is the inspection result normal?

    YES 

    Replace around view monitor control unit. Refer to REMOVAL AND INSTALLATION .

    NO 

    Replace LH side camera. Refer to REMOVAL AND INSTALLATION .

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.