Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSNISSAN-DATSUN2015ROGUE SV, AWDREPAIR AND DIAGNOSIS (SINGLE PAGE)ACCESSORIES & EQUIPMENTCRUISE CONTROL SYSTEMSDRIVER ASSISTANCE SYSTEM (CHASSIS CONTROL)SYSTEM DESCRIPTIONDIAGNOSIS SYSTEM (CHASSIS CONTROL MODULE)CONSULT FUNCTIONDATA MONITOR
2015 Nissan-Datsun Rogue SV, AWD
Data Monitor
2015 Nissan-Datsun Rogue SV, AWDSECTION Data Monitor
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items.
| Item [Unit] |
Description | |
|---|---|---|
| IGN VOLT | [V] | Displays the ignition power supply voltage. |
| CONTROL MODULE MALF | [Off / On] | Displays chassis control module malfunction. |
| CAN DIAG STATUS | [Off / On] | Displays CAN network diagnosis status. |
| VEHICLE SPEED | [km/m] | Displays the vehicle speed. |
| FR WHEEL SPEED | [RPM] | Displays the rotational speed of front RH tire. |
| FL WHEEL SPEED | [RPM] | Displays the rotational speed of front LH tire. |
| RR WHEEL SPEED | [RPM] | Displays the rotational speed of rear RH tire. |
| RL WHEEL SPEED | [RPM] | Displays the rotational speed of rear LH tire. |
| STEERING ANG SENSOR | [deg] | Displays the steering angle from the steering angle sensor. |
| DECEL G SENSOR | [G] | Displays the decel G. |
| SIDE G SENSOR | [G] | Displays the side G. |
| YAW RATE SENSOR | [deg/s] | Displays the yaw rate. |
| ACCELE PEDAL POSITION | [%] | Displays the accelerator pedal position. |
| THROTTLE CONTROL | [NORMAL / INCORR / PREV / INPOSSI] | Displays the electric throttle status. |
| SHIFT POSITION | [Off / P / R / N / D (A) / S / L / B / 1- 6 / M 1 -M 8 / A 1 - A 6] | Displayed but not used. |
| BRAKE SWITCH 2 | [Off / On] | Displays brake switch operating status (Off: close / On: open). |
| BRAKE SWITCH 1 | [Off / On] | Displays brake switch operating status (Off: open / On: close). |
| PRESS SENSOR | [bar] | Displays the brake fluid pressure. |
| ABS | [NORMAL / ABNOR] | Displays ABS function status. |
| ABS MALF | [NORMAL / ABNOR] | Displays ABS function status. |
| EBD | [NORMAL / ABNOR] | Displays EBD function status. |
| ACCELE PEDAL MALF | [NORMAL / ABNOR] | Displays the accelerator pedal status. |
| TCS | [NORMAL / ABNOR] | Displays TCS function status. |
| TCS MALF | [NORMAL / ABNOR] | Displays TCS function status. |
| VDC | [NORMAL / ABNOR] | Displays VDC function status. |
| VDC MALF | [NORMAL / ABNOR] | Displays VDC function status. |
| VDC OFF SWITCH | [Off / On] | Displays VDC OFF switch status. |
| PARKING BRAKE | [Off / On] | Displayed but not used. |
| DRV TRQ CTRL MODE | [INITIAL / NORMAL / STOP 1 / STOP 2 / LIMIT 1 / PROHIBI] | Displays the status of correction to slightly increase/decrease the drive torque. |
| DRV TRQ CTRL PERMIS 1 | [NO PER / PERMIS] | Displays the permission status (basic requirement) of correction to slightly increase/decrease drive torque. |
| DRV TRQ CTRL PERMIS 2 | [NO PER / PERMIS] | Displays the permission status (system requirement) of correction to slightly increase/decrease drive torque. |
| DRV TRQ CTRL STOP | [REQ / NO REQ] | Displays the stop request status of correction to slightly increase/decrease drive torque. |
| DRV TRQ CTRL PROHIBIT | [REQ / NO REQ] | Displays the procedures request status of correction to slightly increase/decrease drive torque. |
| AEB | [Off / On] | Displays the Active Engine Brake (corner) function operating status |
| ATC 1 | [Off / On] | Displays active trace control function operating status. |
| ATC 2 | [Off / On] | Displays active trace control function operating status. |
| ATC 3 | [Off / On] | Displays active trace control function operating status. |
| ATC 4 | [Off / On] | Displays active trace control function operating status. |
| ATC 5 | [Off / On] | Displays active trace control function operating status. |
| BRAKE HOLD | [INACT / ACT / RELEA] | Displays the status of Hill Start Assist function. |
| ARC BRAKE | [Off / On] | Displays the brake control effect of Active Trace Control function on the information display in the combination meter. |
| FL TIRE DISP | [DEF / 1] | Displays tire status. |
| FR TIRE DISP | [DEF / 1] | Displays tire status. |
| RL TIRE DISP | [DEF / 1] | Displays tire status. |
| RR TIRE DISP | [DEF / 1] | Displays tire status. |
| VEHICLE DISP | [Off / On] | Displays Active Ride Control (brake) activation status. |
| INTERRUPT DISP | [NOREQ / HOLD1 / HOLD2 / HDC] | Displays the interruption status. |
| TURN DISP | [NSTEER / LEFT / RIGHT] | Displays the turn status. |
| ALC LEVEL | [0] | Displayed but not used. |
| ALC STATUS | [ACTIVE / INACT] | Displayed but not used. |
| BRAKE HOLD DISP | [INACT / ACT / RELEA] | Displays the brake hold status. |
| ATC DISP | [Off / On] | Displays Active Trace Control status. |
| ARC BRAKE DISP | [Off / On] | Displays the status of Active Ride Control (brake). |
| HDC DISP | [Off / On] | Displays the Hill Descent Control. |
| CVT ENABLE | [Off / On] | Displays the CVT authorized state for Active Engine Brake. |
| ADA SW | [Off / On] | Displays the Active Engine Brake status. |
| COMMAND(REL) | [0.0000] | Displays the relative command value of Active Engine Brake. |
| COMMAND(ABS) | [0.0000] | Displays absolute command value of Active Engine Brake. |
| SLIP RATE | [%] | Displays slip ratio of Active Engine Brake. |
| ASA CHARACTERISTIC | [Off / On] | Displays Active Trace Control state on METER. |
| ADA CHARACTERISTIC | [Off / On] | Displays Active Engine Brake state on METER. |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.