SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSNISSAN-DATSUN2015JUKE SL, 4WDREPAIR AND DIAGNOSISENGINE PERFORMANCETESTING & DIAGNOSISENGINE CONTROL SYSTEM (EXCEPT NISMO RS - DTC TESTS P0138-P046E)DTC/CIRCUIT DIAGNOSISDTC P0441: EVAP CONTROL SYSTEMDTC LOGICDTC CONFIRMATION PROCEDURE
2015 Nissan-Datsun Juke SL, 4WD

DTC Confirmation Procedure

2015 Nissan-Datsun Juke SL, 4WDSECTION DTC Confirmation Procedure

  1. INSPECTION START

    Will CONSULT be used?

    Will CONSULT be used?

    YES 

    GO TO STEP 2. 

    NO 

    GO TO STEP 6. 

  2. PRECONDITIONING

    If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

    1. Turn ignition switch OFF and wait at least 10 seconds.
    2. Turn ignition switch ON.
    3. Turn ignition switch OFF and wait at least 10 seconds.

    TESTING CONDITION: 

    Always perform test at a temperature of 5°C (41°F) or more. 

    GO TO STEP 3. 

  3. PERFORM DTC CONFIRMATION PROCEDURE-I

    With CONSULT 

    1. Start engine and warm it up to normal operating temperature.
    2. Turn ignition switch OFF and wait at least 10 seconds.
    3. Turn ignition switch ON.
    4. Turn ignition switch OFF and wait at least 10 seconds.
    5. Start engine and let it idle for at least 70 seconds.
    6. Select "PURG FLOW P0441" of "EVAPORATIVE SYSTEM" in "DTC WORK SUPPORT" mode with CONSULT.
    7. Touch "START".

    Is "COMPLETED" displayed on CONSULT screen?

    YES 

    GO TO STEP 5. 

    NO 

    GO TO STEP 4. 

  4. PERFORM DTC CONFIRMATION PROCEDURE-II

    When the following conditions are met, "TESTING" will be displayed on the CONSULT screen. Maintain the conditions continuously until "TESTING" changes to "COMPLETED". (It will take at least 35 seconds.)

    Selector lever Suitable position
    VHCL SPEED SE 32 - 120 km/h (20 - 75 mph)
    ENG SPEED 500 - 3, 000 RPM
    B/FUEL SCHDL 1.25 - 6.5 msec
    COOLANT TEMP/S More than 0°C (32°F)
    CAUTION:

    Always drive vehicle at a safe speed.

    If "TESTING" does not change for a long time, retry from step 2. 

    Is "COMPLETED" displayed on CONSULT screen?

    YES 

    GO TO STEP 5. 

    NO 

    Perform DTC CONFIRMATION PROCEDURE again. GO TO STEP 3. 

  5. PERFORM DTC CONFIRMATION PROCEDURE-III

    Touch "SELF-DIAG RESULTS".

    Which is displayed on CONSULT screen?

    OK 

    INSPECTION END

    NG 

    Proceed to DIAGNOSIS PROCEDURE .

  6. PERFORM COMPONENT FUNCTION CHECK

    Perform component function check. Refer to COMPONENT FUNCTION CHECK .

    NOTE:

    Use component function check to check the overall monitoring function of the EVAP control system purge flow monitoring. During this check, a 1st trip DTC might not be confirmed.

    Is the inspection result normal?

    YES 

    INSPECTION END

    NO 

    Proceed to DIAGNOSIS PROCEDURE .

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.