SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSNISSAN-DATSUN2015JUKE SL, 4WDREPAIR AND DIAGNOSISENGINE PERFORMANCETESTING & DIAGNOSISENGINE CONTROL SYSTEM (EXCEPT NISMO RS - DTC TESTS P0138-P046E)DTC/CIRCUIT DIAGNOSISDTC P0181: FTT SENSORDTC LOGICDTC CONFIRMATION PROCEDURE
2015 Nissan-Datsun Juke SL, 4WD

DTC Confirmation Procedure

2015 Nissan-Datsun Juke SL, 4WDSECTION DTC Confirmation Procedure

  1. INSPECTION START

    Is it necessary to erase permanent DTC?

    YES 

    GO TO STEP 7  .

    NO 

    GO TO STEP 2  .

  2. PRECONDITIONING

    If DTC CONFIRMATION PROCEDURE has been previously conducted, always perform the following procedure before conducting the next test.

    1. Turn ignition switch OFF and wait at least 10 seconds.
    2. Turn ignition switch ON.
    3. Turn ignition switch OFF and wait at least 10 seconds.

    GO TO STEP 3  .

  3. PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A-I

    1. Turn ignition switch ON and wait at least 10 seconds.
    2. Check 1st trip DTC.

    Is 1st trip DTC detected?

    YES 

    Proceed to DIAGNOSIS PROCEDURE .

    NO 

    GO TO STEP 4  .

  4. CHECK ENGINE COOLANT TEMPERATURE

    With CONSULT

    1. Select "COOLANT TEMP/S" in "DATA MONITOR" with CONSULT.
    2. Check "COOLANT TEMP/S" value.

    With GST

    Follow the procedure "With CONSULT" above.

    "COOLANT TEMP/S" less than 60°C (140°F)?

    YES 

    INSPECTION END

    NO 

    GO TO STEP 5  .

  5. PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A-II

    With CONSULT

    1. Cool engine down until "COOLANT TEMP/S" is less than 60°C (140°F).
    2. Wait at least 10 seconds.
    3. Check 1st trip DTC.

    With GST

    Follow the procedure "With CONSULT" above.

    Is 1st trip DTC detected?

    YES 

    Proceed to DIAGNOSIS PROCEDURE .

    NO 

    GO TO STEP 6  .

  6. PERFORM COMPONENT FUNCTION CHECK (FOR MALFUNCTION B)

    Perform component function check. Refer to COMPONENT FUNCTION CHECK .

    NOTE:

    Use the component function check to check the overall function of the FTT sensor circuit. During this check, a 1st trip DTC might not be confirmed.

    Is the inspection result normal?

    YES 

    INSPECTION END

    NO 

    Proceed to DIAGNOSIS PROCEDURE .

  7. PRECONDITIONING

    If DTC CONFIRMATION PROCEDURE has been previously conducted, always perform the following procedure before conducting the next test.

    1. Turn ignition switch OFF and wait at least 10 seconds.
    2. Turn ignition switch ON.
    3. Turn ignition switch OFF and wait at least 10 seconds.

    TESTING CONDITION: 

    • Before performing the following procedure, do not add fuel. 
    • Before performing the following procedure, check that fuel level is between 1/4 and 4/4. 
    • Before performing the following procedure, confirm that battery voltage is 11 V or more at idle. 

    GO TO STEP 8  .

  8. PERFORM DTC CONFIRMATION PROCEDURE B

    1. Move the vehicle to a cool place.
      NOTE:

      Cool the vehicle in an environment of ambient air temperature between - 10°C (14°F) and 35°C (95°F).

    2. Turn ignition switch OFF and leave the vehicle for 12 hours.
      CAUTION:

      Never turn ignition switch ON during this procedure.

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.