Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Data Monitor
2015 Nissan-Datsun Juke SL, 4WDSECTION Data Monitor
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items.
: Applicable
| Item (Unit) | Monitor item selection | Note | |
|---|---|---|---|
| ECU INPUT SIGNALS | MAIN SIGNALS | ||
| FR LH SENSOR [km/h (MPH)] |
* | * | Wheel speed calculated by front LH wheel sensor is displayed. |
| FR RH SENSOR [km/h (MPH)] |
* | * | Wheel speed calculated by front RH wheel sensor is displayed. |
| RR LH SENSOR [km/h (MPH)] |
* | * | Wheel speed calculated by rear LH wheel sensor is displayed. |
| RR RH SENSOR [km/h (MPH)] |
* | * | Wheel speed calculated by rear RH wheel sensor is displayed. |
| DECEL G-SEN (G) |
* | * | Decel G detected by decel G sensor is displayed. |
| FR RH IN SOL (On/Off) |
* | Operation status of front RH wheel ABS IN valve is displayed. | |
| FR RH OUT SOL (On/Off) |
* | Operation status of front RH wheel ABS OUT valve is displayed. | |
| FR LH IN SOL (On/Off) |
* | Operation status of front LH wheel ABS IN valve is displayed. | |
| FR LH OUT SOL (On/Off) |
* | Operation status of front LH wheel ABS OUT valve is displayed. | |
| RR RH IN SOL (On/Off) |
* | Operation status of rear RH wheel ABS IN valve is displayed | |
| RR RH OUT SOL (On/Off) |
* | Operation status of rear RH wheel ABS OUT valve is displayed. | |
| RR LH IN SOL (On/Off) |
* | Operation status of rear LH wheel ABS IN valve is displayed. | |
| RR LH OUT SOL (On/Off) |
* | Operation status of rear LH wheel ABS OUT valve is displayed. | |
| EBD WARN LAMP (On/Off) |
Brake warning lamp ON/OFF status is displayed. * | ||
| STOP LAMP SW (On/Off) |
* | * | Stop lamp switch signal input status is displayed. |
| MOTOR RELAY (On/Off) |
* | ABS motor and motor relay status is displayed. | |
| ACTUATOR RLY (On/Off) |
* | ABS actuator relay status is displayed. | |
| ABS WARN LAMP (On/Off) |
* | ABS warning lamp ON/OFF status is displayed. * | |
| OFF LAMP (On/Off) |
* | VDC OFF indicator lamp ON/OFF status is displayed. * | |
| OFF SW (On/Off) |
* | * | VDC OFF switch signal input status is displayed. |
| SLIP/VDC LAMP (On/Off) |
* | VDC warning lamp ON/OFF status is displayed. * | |
| BATTERY VOLT (V) |
* | * | Voltage supplied to ABS actuator and electric unit (control unit) is displayed. |
| GEAR | * | * | Current gear position judged from current gear position signal is displayed. |
| ENGINE SPEED [tr/min (RPM)] |
* | * | Engine speed status is displayed. |
| YAW RATE SEN (d/s) |
* | * | Yaw rate detected by yaw rate sensor is displayed. |
| R POSI SIG (On/Off) |
R range signal input status judged from R range signal is displayed. | ||
| 4WD MODE MON (2WD/AUTO) |
* | * | AWD control status is displayed. |
| N POSI SIG (On/Off) |
N range signal input status judged from N range signal is displayed. | ||
| P POSI SIG (On/Off) |
P range signal input status judged from P range signal is displayed. | ||
| CV1 (On/Off) |
Cut valve 1 operation status is displayed. | ||
| CV2 (On/Off) |
Cut valve 2 operation status is displayed. | ||
| SV1 (On/Off) |
Suction valve 1 operation status is displayed. | ||
| SV2 (On/Off) |
Suction valve 2 operation status is displayed. | ||
| STOP LAMP SW2 (On/Off) |
Brake pedal position switch signal input status is displayed. | ||
| ACCEL POS SIG (%) |
* | Displays the Accelerator pedal position | |
| SIDE G-SENSOR (m/s2) |
* | Side G detected by side G sensor is displayed. | |
| STR ANGLE SIG (deg) |
* | Steering angle detected by steering angle sensor is displayed. | |
| EBD SIGNAL (On/Off) |
EBD operation status is displayed. | ||
| ABS SIGNAL (On/Off) |
ABS operation status is displayed. | ||
| TCS SIGNAL (On/Off) |
TCS operation status is displayed. | ||
| VDC SIGNAL (On/Off) |
VDC operation status is displayed. | ||
| EBD FAIL SIG (On/Off) |
EBD fail-safe signal status is displayed. | ||
| ABS FAIL SIG (On/Off) |
ABS fail-safe signal status is displayed. | ||
| TCS FAIL SIG (On/Off) |
TCS fail-safe signal status is displayed. | ||
| VDC FAIL SIG (On/Off) |
VDC fail-safe signal status is displayed. | ||
| CRANKING SIG (On/Off) |
Cranking status is displayed. | ||
| FLUID LEV SW (On/Off) |
* | Brake fluid level signal input status via CAN communication is displayed. | |
* : Refer to SYSTEM DESCRIPTION for ON/OFF conditions of each warning lamp.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.