SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSNISSAN-DATSUN2015JUKE SL, 4WDREPAIR AND DIAGNOSIS (SINGLE PAGE)ENGINE PERFORMANCESYSTEMENGINE CONTROL SYSTEM (EXCEPT NISMO RS - INTRODUCTION)SYSTEM DESCRIPTIONDIAGNOSIS SYSTEM (ECM)CONSULT FUNCTIONACTIVE TEST MODE
2015 Nissan-Datsun Juke SL, 4WD

Active Test Mode

2015 Nissan-Datsun Juke SL, 4WDSECTION Active Test Mode

Test Item 

Test item Condition Judgement Check item (Remedy)
ENG COOLANT TEMP
  • Engine: Return to the original trouble condition
  • Change the engine coolant temperature using CONSULT.
 If trouble symptom disappears, see Check item.
  • Harness and connectors
  • Engine coolant temperature sensor
  • Fuel injector
FUEL INJECTION
  • Engine: Return to the original trouble condition
  • Change the amount of fuel injection using CONSULT.
 If trouble symptom disappears, see Check item.
  • Harness and connectors
  • Fuel injector
  • Air fuel ratio (A/F) sensor 1
PURG VOL CONT/V
  • Engine: After warming up, run engine at 1, 500 RPM.
  • Change the EVAP canister purge volume control solenoid valve opening percent using CONSULT.
 Engine speed changes according to the opening percent.
  • Harness and connectors
  • Solenoid valve
FUEL PUMP RELAY
  • Ignition switch: ON
  • Engine stopped
  • Turn the fuel pump relay "ON" and "OFF" using CONSULT and listen to operating sound.
 Fuel pump relay makes the operating sound.
  • Harness and connectors
  • Fuel pump relay
IGNITION TIMING
  • Engine: Return to the original trouble condition
  • Timing light: Set
  • Retard the ignition timing using CONSULT.
 If trouble symptom disappears, see Check item. Perform Idle Air Volume Learning.
FAN DUTY CONTROL*
  • Ignition switch: ON
  • Change duty ratio using CONSULT.
 Cooling fan speed changes.
  • Harness and connectors
  • Cooling fan motor
  • Cooling fan relay
  • Cooling fan control module
  • IPDM E/R
ALTERNATOR DUTY
  • Ignition switch: ON
  • Change duty ratio using CONSULT.
 Battery voltage changes.
  • Harness and connectors
  • Alternator
  • IPDM E/R
POWER BALANCE
  • Engine: After warming up, idle the engine.
  • A/C switch OFF
  • Shift lever: P or N (CVT), Neutral (M/T)
  • Cut off each fuel injector signal one at a time using CONSULT.
 Engine runs rough or dies.
  • Harness and connectors
  • Compression
  • Fuel injector
  • Power transistor
  • Spark plug
  • Ignition coil
EGR CONTROL VALVE
  • Ignition switch: ON
  • Engine stopped
  • Change valve target angle using CONSULT
 Valve opening angle changes according to target angle (from 0 deg to 70 deg)
  • Harness and connectors
  • EGR valve
VALVE TIMING OFFSET DATA WRITING
  • Ignition switch: ON
  • Engine stopped
  • Change the wastegate target stroke using CONSULT
 Wastegate position sensor output voltage changes according to target stroke value.
  • Harness and connectors
  • Wastegate actuator (Removal wastegate actuator from turbocharger is NG)
  • Turbocharger assembly
TC BYPASS VALVE
  • Ignition switch: ON
  • Engine stopped or Engine running (idling, less than 1200 RPM)
  • Input "ON""OFF" signal using CONSULT
 Bypass valve makes the operating sound.
  • Harness and connectors
  • Turbocharger bypass valve (Removal bypass valve from Turbocharger is NG)
  • Turbocharger assembly
ENGINE OIL PRESSURE CONTROL SOLENOID VALVE
  • Water temperature: > - 10°C
  • Engine oil temperature: < 120°C (248°F)
  • Engine speed: < 4000 RPM
 Engine oil pressure change
  • Harness and connectors
  • Engine oil pressure control solenoid valve
  • Engine oil pressure sensor
  • Engine oil pump
SWRL CONT S/V VALVE
  • Ignition switch: ON
  • Engine stopped
  • Turn the intake manifold runner control valve "ON" and "OFF" using CONSULT to open or close.
 Touch the intake manifold runner control valve motor and check the operating vibration and sound.
  • Harness and connectors
  • Intake manifold runner control valve
  • Intake manifold runner control valve motor
AUTO STOP START
  • Engine: After warming up, run engine at idle
  • Shift lever: Neutral position
  • "Start" and "Cancel" using CONSULT.
 Check the stop/start system operate and restart.
  • Harness and connectors
  • IPDM E/R
  • Starter motor
  • Engine restart relay
  • Starter control relay
  • DC/DC converter
  • Battery
CAUTION:

Be careful so that a hood operates in the opened state when carry out work.
WASTEGATE ACTUATOR
  • Ignition switch: ON
  • Engine stopped
  • Change valve of wastegate actuator target angle using CONSULT
 Wastegate valve position sensor voltage changes according to valve target angle
  • Harness and connectors
  • Electric wastegate control actuator (Removal bypass valve from turbocharger is NG)
  • Turbocharger assembly
VENT CONTROL/V
  • Ignition switch: ON
  • Engine stopped
  • Turn solenoid valve ON and OFF with the CONSULT and listen to operating sound.
 Solenoid valve makes an operating sound.
  • Harness and connectors
  • EVAP canister vent control solenoid valve

* : Leaving cooling fan OFF with CONSULT while engine is running may cause the engine to overheat.

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.