SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSNISSAN-DATSUN2015JUKE SL, 4WDREPAIR AND DIAGNOSIS (SINGLE PAGE)ACCESSORIES & EQUIPMENTINFOTAINMENTAUDIO, VISUAL & NAVIGATION SYSTEM (AUDIO WITH NAVIGATION)DTC/CIRCUIT DIAGNOSISDTC U111C: FRONT CAMERA IMAGE SIGNAL CIRCUITDIAGNOSIS PROCEDURE
2015 Nissan-Datsun Juke SL, 4WD

Diagnosis Procedure

2015 Nissan-Datsun Juke SL, 4WDSECTION Diagnosis Procedure

  1. CHECK CONTINUITY FRONT CAMERA POWER SUPPLY AND GROUND CIRCUIT

    1. Turn ignition switch OFF.
    2. Disconnect around view monitor control unit connector and front camera connector.
    3. Check continuity between around view monitor control unit harness connector and front camera harness connector.
      Around view monitor control unit Front camera Continuity
      Connector Terminals Connector Terminals
      M98 5 E72 2 Existed
      6 1
    4. Check continuity between around view monitor control unit harness connector and ground.
      Around view monitor control unit Ground Continuity
      Connector Terminal
      M98 6 Not existed

    Is inspection result normal?

    YES 

    GO TO STEP 2  .

    NO 

    Repair harness or connector.

  2. CHECK VOLTAGE FRONT CAMERA POWER SUPPLY

    1. Connect around view monitor control unit connector and front camera connector.
    2. Turn ignition switch ON.
    3. Check voltage between around view monitor control unit harness connector and ground.
      Terminal Standard voltage Reference voltage
      (Approx.)
      (+) (-)
      Around view monitor control unit
      Connector Terminal Connector Terminal
      M98 6 M98 5 3.5 V or more 6.0 V

    Is inspection result normal?

    YES 

    GO TO STEP 3  .

    NO 

    Replace around view monitor control unit. Refer to REMOVAL AND INSTALLATION .

  3. CHECK CONTINUITY CAMERA IMAGE SIGNAL CIRCUIT

    1. Turn ignition switch OFF.
    2. Disconnect around view monitor control unit connector and front camera connector.
    3. Check continuity between around view monitor control unit harness connector and front camera harness connector.
      Around view monitor control unit Front camera Continuity
      Connector Terminals Connector Terminals
      M98 7 E72 4 Existed
      8 3
    4. Check continuity between around view monitor control unit harness connector and ground.
      Around view monitor control unit Ground Continuity
      Connector Terminals
      M98 7 Not existed
      8

    Is inspection result normal?

    YES 

    GO TO STEP 4  .

    NO 

    Repair harness or connector.

  4. CHECK CAMERA IMAGE SIGNAL

    1. Connect around view monitor control unit connector and front camera connector.
    2. Turn ignition switch ON.
    3. Check signal between around view monitor control unit harness connector terminals.
      Terminal Condition Reference value
      (+) (-)
      Around view monitor control unit
      Connector Terminal Connector Terminal
      M98 8 M98 7 Shift position is in "R".
      GNSJSNIA0834GB-834Courtesy of NISSAN NORTH AMERICA, INC.

    Is inspection result normal?

    YES 

    Replace around view monitor control unit. Refer to REMOVAL AND INSTALLATION .

    NO 

    Replace front camera. Refer to REMOVAL AND INSTALLATION .

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.