Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSNISSAN-DATSUN2013MURANO CROSSCABRIOLETREPAIR AND DIAGNOSISGENERAL INFORMATIONSPECIFICATIONS INDEXCOMMON SPECS & PROCEDURES (CROSSCABRIOLET)COMMON SPECIFICATIONS & PROCEDURES
2013 Nissan-Datsun Murano CrossCabriolet
Common Specifications & Procedures
2013 Nissan-Datsun Murano CrossCabrioletSECTION Common Specifications & Procedures
MURANO CROSSCABRIOLET COMMON SPECIFICATIONS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Torque | See Torque Specifications in Text and applicable figures in REMOVAL AND INSTALLATION . | ||
| Axle Nut/Hub Bearing Bolts | |||
| Front Axle Nut | 177 Ft. lbs (240 N.m) | ||
| Front Hub Bearing Bolts | 65 Ft. lbs (88.3 N.m) | ||
| Rear Axle Nut | 129 Ft. lbs (175 N.m) | ||
| Rear Hub Bearing Bolts | 65 Ft. lbs (88.3 N.m) | ||
| Battery | BATTERY | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING BRAKE SYSTEM | ||
| Disc Brakes | |||
| Front | FRONT DISC BRAKE | ||
| Rear | REAR DISC BRAKE | ||
| Torque | |||
| Front | See Torque Specifications in Text and applicable graphics in FRONT DISC BRAKE . | ||
| Rear | See Torque Specifications in Text and applicable graphics in REAR DISC BRAKE . | ||
| Charging | |||
| Generator | ALTERNATOR | ||
| Torque | See Torque Specifications in Text and applicable figures in REMOVAL AND INSTALLATION . | ||
| Drive Belts | |||
| Adjustment | Vehicle equipped with auto tensioner | ||
| Belt Routing | DRIVE BELT | ||
| Engine Cooling | |||
| General Service Specifications | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Radiator Cap Pressure | 17.7-22 psi (122.3-151.7 kPa, 1.2-1.5 kgf/cm2 ) | ||
| Thermostat R & I | WATER INLET AND THERMOSTAT ASSEMBLY | ||
| Water Pump R & I | WATER PUMP | ||
| Engine Mechanical | |||
| Compression | COMPRESSION PRESSURE | ||
| Oil Pressure | |||
| @ Idle | More than 14 psi (98 kPa, 1.0 kg/cm2 ) | ||
| @ 2000 RPM | More than 43 psi (294 kPa, 3.0 kg/cm2 ) | ||
| Overhaul | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Torque | See Torque Specifications in Text and applicable figures in REMOVAL AND INSTALLATION . | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate (Drive Plate) Torque | 65 Ft. lbs (88 N.m) | ||
| Fuel System | |||
| Fuel Pressure Release Procedure | FUEL PRESSURE RELEASE | ||
| Fuel Pressure | At idling: Approximately 51 psi (350 kPa, 3.57 kg/cm2 ) | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE CHECK | ||
| Fuel Filter Location | In Tank Type | ||
| Fuel Filter R & I | FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Engine has coil-on-plug ignition. | ||
| Ignition Wires (Routing) | Engine has coil-on-plug ignition. | ||
| Spark Plugs | SPARK PLUG Tightening torque: 14 Ft. lbs (19.6 N.m) |
||
| Starting | |||
| Starter | STARTER MOTOR | ||
| Torque | See Torque Specifications in Text and applicable graphics under REMOVAL AND INSTALLATION . | ||
| Wheel Alignment | |||
| Adjustment Specifications | |||
| Front | WHEEL ALIGNMENT | ||
| Rear | WHEEL ALIGNMENT | ||
| Torque | |||
| Front | See Torque Specifications in Text and applicable figures in REMOVAL AND INSTALLATION . | ||
| Rear | See Torque Specifications in Text and applicable figures in REMOVAL AND INSTALLATION . | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 80 Ft. lbs (108 N.m, 11 kg.m) | ||
| How To Use Nissan Service Information | |||
| Includes: Standard Bolt Torque Symbol Identification General Connector Info |
GENERAL INFORMATION (CROSSCABRIOLET) | ||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.