2004 Nissan-Datsun Sentra SE-RFACTORY OEM SERVICE PROCEDURE

Fuel Level Sensor Signal Inspection

WARNING: This page is about a different car, the 2005 Nissan 350Z. However, it is still accessible from the selected car via links, so may be relevant.

Symptom:

  • Fuel gauge indication is malfunction.
  • Low-fuel warning lamp indication is irregular.
NOTE: The following symptoms are not malfunction.

Fuel level sensor unit

  • Depending on vehicle position or driving circumstance, the fuel level in the tank various, and the pointer may fluctuate.
  • If the vehicle is fueled with the ignition switch ON, the pointer will move slowly.

Low-fuel warning lamp

  • Depending on vehicle position or driving circumstance, the fuel in the tank flows and the warning lamp ON timing may change.
  1. CHECK UNIFIED METER AND A/C AMP. INPUT SIGNAL 
    1. Select "METER A/C AMP" on CONSULT-II.
    2. Using "FUEL METER" on "DATA MONITOR", compare the value of "DATA MONITOR" with fuel gauge pointer of combination meter.
      FUEL GAUGE INDICATION - VALUE ON MONITOR

      Fuel gauge indication Value on monitor [lit.]
      Full Approx. 74
      Three quarters Approx. 61
      Half Approx. 42
      A quarter Approx. 22
      Empty Approx. 8
      Fig 1: Scan Tool Display "Data Monitor Fuel Meter"
      G02405964Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    • OK : GO TO 2.
    • NG : Replace combination meter.
  2. CHECK FUEL LEVEL SENSOR 
    1. Turn ignition switch OFF.
    2. Check components. Refer to "FUEL LEVEL SENSOR UNIT CHECK ".

    OK or NG 

    • OK : GO TO 3.
    • NG : Replace fuel level sensor unit.
  3. CHECK FUEL LEVEL SENSOR (SUB) CIRCUIT 
    1. Disconnect unified meter and A/C amp. connector and fuel level sensor unit (sub) connector.
    2. Check continuity between unified meter and A/C amp. harness connector M49 terminal 28 (W/B) and fuel level sensor unit (sub) harness connector B28 terminal 1 (W/B).
      • 28 (W/B) - 1 (W/B) : Continuity should exist. 
    3. Check continuity between unified meter and A/C amp. harness connector M49 terminal 28 (W/B) and ground.
      • 28 (W/B) - Ground : Continuity should not exist. 
      Fig 2: Unified Meter & A/C AMP. Harness Connector M49 Terminal 28 (W/B) & Ground Continuity Test
      G02405965Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    • OK : GO TO 4.
    • NG : Repair harness or connector.
  4. CHECK FUEL LEVEL SENSOR (MAIN SUB) CIRCUIT 
    1. Disconnect fuel level sensor unit and fuel pump (main) connector.
    2. Check continuity between fuel level sensor unit (sub) harness connector B28 terminal 2 (Y) and fuel level sensor unit and fuel pump (main) harness connector B27 terminal 2 (Y).
      • 2 (Y) - 2 (Y) : Continuity should exist. 
    3. Check continuity between fuel level sensor unit (sub) harness connector B28 terminal 2 (Y) and ground.
      • 2 (Y) - Ground : Continuity should not exist. 
      Fig 3: Fuel Level Sensor Unit (Sub) Harness Connector B28 Terminal 2 (Y) & Ground Continuity Test
      G02405966Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    • OK : GO TO 5.
    • NG : Repair harness or connector.
  5. CHECK FUEL LEVEL SENSOR (MAIN) CIRCUIT 
    1. Check continuity between fuel level sensor unit and fuel pump (main) harness connector B27 terminal 5 (B/R) and unified meter and A/C amp. harness connector M49 terminal 36 (R/B).
      • 5 (B/R) - 36 (R/B) : Continuity should exist. 
    2. Check continuity between fuel level sensor unit and fuel pump (main) harness connector B27 terminal 5 (B/R) and ground.
      • 5 (B/R) - Ground : Continuity should not exist. 
      Fig 4: Fuel Level Sensor Unit & Fuel Pump (Main) Harness Connector B27 Terminal 5 (B/R) & Ground Continuity Test
      G02405967Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    • OK : GO TO 6.
    • NG : Repair harness or connector.
  6. CHECK INSTALLATION CONDITION 

    Check fuel level sensor unit installation, and check whether the float arm interferes or binds with any of the Internal components in the fuel tank.

    OK or NG 

Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.