Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSNISSAN-DATSUN2001MAXIMA GXE, AUTOMATIC, RE4F04WREPAIR AND DIAGNOSISENGINE PERFORMANCESYSTEMENGINE CONTROLS - SELF-DIAGNOSTICS
2001 Nissan-Datsun Maxima GXE, Automatic, RE4F04W
Engine Controls - Self-Diagnostics
2001 Nissan-Datsun Maxima GXE, Automatic, RE4F04WSECTION Engine Controls - Self-Diagnostics
- Introduction
- Self-Diagnostic System
- Programming
- Summary
- Diagnostic Trouble Code Definitions
- Diagnostic Tests
- DTC P0100: Mass Airflow (MAF) Sensor
- DTC P0105: Absolute Pressure (AP) Sensor
- DTC P0110: Intake Air Temperature (IAT) Sensor
- DTC P0115 Or P0125: Engine Coolant Temperature (ECT) Sensor
- DTC P0120: Throttle Position (TP) Sensor
- DTC P0130: Right Bank, Or DTC P0150: Left Bank Front Heated Oxygen Sensor
- DTC P0131 Or P0132: Right Bank, Or DTC P0151 Or P0152: Left Bank Front Heated Oxygen Sensor
- DTC P0133: Right Bank, Or DTC P0153: Front Heated Oxygen Sensor
- DTC P0134: Right Bank, Or DTC P0154: Left Bank Front Heated Oxygen Sensor
- DTC P0135: Right Bank, Or DTC P0155: Left Bank Front Ho2S Heater
- DTC P0137, P0138, P0139, P0140, P0157: Right Bank, Or DTC P0158, P0159, Or P0160: Left Bank Rear Heated Oxygen Sensor
- DTC P0141: Right Bank, Or DTC P0161: Left Bank Rear Ho2S Heater
- DTC P0171, P0172, P0174 Or P0175: Fuel Injection System Function (Right Or Left Bank)
- DTC P0180: Fuel Tank Temperature (FTT) Sensor
- DTC P0217: Coolant OVERTEMPERATURE Enrichment Protection, Or DTC P1217: Engine Overheat
- DTC P0300-P0306: Cylinder Or Multiple Cylinder Misfire
- DTC P0325: Knock Sensor
- DTC P0335 Or P1336: Crankshaft Position (CKP) Sensor (Pos)
- DTC P0340: Camshaft Position (CMP) Sensor
- DTC P0420 Or P0430: Three-Way Catalyst Function
- DTC P0440 Or P1440: EVAP Control System (Small Leak)
- DTC P0443: EVAP Canister Purge Volume Control Valve (EVAP-CPVCV)
- DTC P0446: EVAP Canister Vent Control Valve (EVAP-CVCV)
- DTC P0450: EVAP Control System Pressure Sensor (EVAP-CSPS)
- DTC P0455: EVAP Control System (Large Leak)
- DTC P0460: Fuel Level Sensor Function (Slosh)
- DTC P0461: Fuel Level Sensor Function
- DTC P0464: Fuel Level Sensor Circuit
- DTC P0500: Vehicle Speed Sensor (VSS)
- DTC P0505: Idle Air Control Valve-Auxiliary Air Control (IACV-AAC) Valve
- DTC P0510: Closed Throttle Position (TP) Switch
- DTC P0600: A/T Communication Line
- DTC P0605: ECM
- DTC P1126: Thermostat Function
- DTC P1130: Swirl Control Valve (SCV) Solenoid
- DTC P1148 Or P1168: Closed Loop Control
- DTC P1165: Swirl Control Vacuum Check Switch
- DTC P1212: Abs/TCS Communication Line
- DTC P1217: Engine Overheat
- DTC P1320: Ignition Signal
- DTC P1335: Crankshaft Position (CKP) Sensor (Ref)
- DTC P1336: Crankshaft Position (CKP) Sensor (Pos)
- DTC P1440: EVAP Control System
- DTC P1444: EVAP Canister Purge Volume Control Valve (EVAP-CPVCV)
- DTC P1446: EVAP Canister Vent Control Valve (EVAP-CVCV)
- DTC P1447: EVAP Control System Purge Flow Monitoring
- DTC P1448: EVAP Canister Vent Control Valve (EVAP-CVCV)
- DTC P1464: Fuel Level Sensor Circuit (Ground Signal)
- DTC P1490: Vacuum Cut Valve By-Pass Valve
- DTC P1491: Vacuum Cut Valve By-Pass Valve
- DTC P1605: Automatic Transmission (A/T) Control
- DTC P1706: Park/Neutral Position (PNP) Switch
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.