Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMITSUBISHI2012LANCER RALLIARTREPAIR AND DIAGNOSIS (SINGLE PAGE)ELECTRICALGAUGESCOMBINATION METER - LANCERON-VEHICLE SERVICESERVICE REMINDER FUNCTION SETHOW TO SET THE SCHEDULE
2012 Mitsubishi Lancer Ralliart
How To Set The Schedule
2012 Mitsubishi Lancer RalliartSECTION How To Set The Schedule
- Turn the ignition switch to the "OFF" position.
- By operating the meter information switch, the warning period is displayed on the multi information display.
- Press the meter information switch once for 1.2 seconds or longer.
- The service reminder indicator flashes.
- While the service reminder indicator flashes, press the meter information switch for 1.2 seconds or longer and 3 times consecutively.
- The service reminder indicator is turned ON, and the current schedule is displayed on the multi information display.
- While the current schedule is displayed, press the meter information switch for less than 1.2 seconds and 3 times consecutively.
- The multi information display is shifted to the schedule selection mode.
- When the meter information switch is pressed for less than 1.2 seconds, the schedule is shifted, and when the meter information switch is pressed for 1.2 seconds or longer, the displayed schedule is set.NOTE: For schedule, "JPN", "GCC/EXP", "EU" and "AUS" can also be selected. However, the setting shall be for "NAS" only.
- The schedule set in Step 9 is displayed for 3 seconds, and the warning period to the next time is displayed.
SCHEDULE TABLE
| Schedule | Contents of schedule | |
|---|---|---|
| NAS 10 (initial setting) < Except RALLIART > | Elapsed time (month) | Every 6 elapsed months |
| Driving distance (miles) | Every 7, 500 miles of driving distance | |
| Driving distance (km) | Every 12, 000 km of driving distance | |
| NAS 11 | Elapsed time (month) | Every 3 elapsed months |
| Driving distance (miles) | Every 3, 750 miles of driving distance | |
| Driving distance (km) | Every 6, 000 km of driving distance | |
| NAS 20 (initial setting) < RALLIART > | Elapsed time (month) | Every 5 elapsed months |
| Driving distance (miles) | Every 5, 000 miles of driving distance | |
| Driving distance (km) | Every 8, 000 km of driving distance | |
| NAS 21 | Elapsed time (month) | Every 4 elapsed months |
| Driving distance (miles) | Every 3, 750 miles of driving distance | |
| Driving distance (km) | Every 6, 000 km of driving distance | |
| Optional INT | The optional schedule can be set. (Only scan tool can be set.) | |
| OFF Display | Without function. "OFF" is displayed on the multi information display. | |
| Function OFF | Without function (Only scan tool can be set.) | |
NOTE:
For schedule, "JPN", "GCC/EXP", "EU" and "AUS" can also be selected. However, the setting shall be for "NAS" only.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.