Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMITSUBISHI2007OUTLANDER LS, FWDREPAIR AND DIAGNOSIS (SINGLE PAGE)ACCESSORIES & EQUIPMENTAUXILIARY POWER UNITCHASSIS ELECTRICAL
2007 Mitsubishi Outlander LS, FWD
Chassis Electrical
2007 Mitsubishi Outlander LS, FWDSECTION Chassis Electrical
- Battery
- Combination Meter
- Service Specifications
- Special Tool
- Diagnosis
- Standard Flow Of Diagnostic Troubleshooting
- Diagnostic Function
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- DTC B1200: Malfunction of odometer
- DTC B1201: Abnormal fuel information; DTC B1202: Abnormal fuel 2 information
- DTC B1208: Malfunction of LCD heater
- DTC B1209: Test mode
- DTC B2203: Chassis No. not programmed
- DTC B2463: Sticking of rheostat switch
- DTC B2464: The sticking of meter information switch
- DTC B2465: Ignition switch signal error
- DTC B2467: Malfunction of stepper motor
- DTC U0019: Bus off(CAN-B)
- DTC U0100: Engine control module CAN timeout
- DTC U0141: ETACS CAN timeout
- DTC U0151: SRS-ECU CAN timeout
- DTC U0154: Occupant classification-ECU CAN timeout
- DTC U0164: A/C-ECU CAN timeout
- DTC U0168: KOS-ECU or WCM CAN timeout
- DTC U0184: Audio CAN timeout
- DTC U0197: Hands free module CAN timeout
- DTC U0245: Audio visual navigation unit CAN timeout
- DTC U1415: Coding not completed/Data fail
- Trouble Symptom Chart
- Trouble Symptom Procedures
- Inspection Procedure 1: Power supply circuit check
- Inspection Procedure 2: The speedometer does not work (the other meters work)
- Inspection Procedure 3: The tachometer does not work (the other meters work)
- Inspection Procedure 4: Tone alarm does not sound normally
- Inspection Procedure 5: The combination meter light does not illuminate normally or the multi information display is not displayed normally
- Inspection Procedure 6: The multi information display screen cannot be changed with the operation of the meter information switch
- Service Data
- Actuator Test Table
- Check Procedure For Each Multi Information Display Screen
- On-Vehicle Service
- Combination Meter Assembly
- Check At Ecu Terminals
- Lighting
- General Information
- Service Specifications
- Special Tools
- Diagnosis
- Standard Flow Of Diagnostic Troubleshooting
- Diagnostic Function
- Service Precautions Discharge Headlight
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- DTC B16A2: Blown turn-signal light (LH) bulb
- DTC B16A3: Turn-signal light (LH) short circuit
- DTC B16A4: Blown turn-signal light (RH) bulb
- DTC B16A5: Turn-signal light (RH) short circuit
- DTC 21: Height sensor abnormality (Rear)
- DTC 22: Height sensor abnormality (Front)
- DTC 23: Height sensor power supply short to ground
- DTC 24: Pitch angle abnormality
- Code No. 31 Leveling unit abnormality
- DTC B16A0: Taillight (RH) circuit open ; DTC B16A7: Taillight (RH) circuit short
- DTC B16A1: Taillight (LH) circuit open ; DTC B16A8: Taillight (LH) circuit short
- DTC B16A6: Turn-signal fuse blown
- Trouble Symptom Chart
- Symptom Procedures
- Inspection Procedure 1: Headlights (low-beam) do not illuminate
- Inspection Procedure 2: Headlights (high-beam) do not illuminate
- Inspection Procedure 3: The headlights do not illuminate when the lighting switch is at the "PASSING" position, but the low-beam illuminates (high-beam and low-beam cannot be changed) with the switch at the "HEAD" position
- Inspection Procedure 4: Headlights do not illuminate when the passing switch is operate
- Inspection Procedure 5: The headlight(s) do not illuminate
- Inspection Procedure 6: High-beam indicator light does not illuminate normally
- Inspection Procedure 7: The headlight automatic shutdown function does not work normally
- Inspection Procedure 8: Daytime running light function does not work normally
- Inspection Procedure 9: Any of position light, side marker lights or the license plate light does not illuminate
- Inspection Procedure 10: The turn-signal lights do not illuminate
- Inspection Procedure 11: The comfort flashing function does not work normally
- Inspection Procedure 12: The turn-signal indicator light do not illuminate
- Inspection Procedure 1: The diagnostic trouble code is not set
- Inspection Procedure 2: Neither right nor left automatic leveling operates
- Inspection Procedure 3: Either automatic leveling does not operate
- Inspection Procedure 4: The headlight automatic leveling warning is not displayed
- Inspection Procedure 5: The headlight automatic leveling warning light does not go off
- Inspection Procedure 1: The taillights do not illuminate
- Inspection Procedure 2: Any of the taillights do not illuminate
- Inspection Procedure 1: Fog lights do not illuminate normally
- Inspection Procedure 2: The right or left fog light does not illuminate
- Inspection Procedure 3: Fog light indicator does not illuminate/go out normally
- Inspection Procedure 1: Daytime running lights do not illuminate normally
- Inspection Procedure 2: The right or left daytime running light does not illuminate
- Inspection Procedure 1: The front dome light does not illuminate normally
- Inspection Procedure 2: The rear dome light does not illuminate normally
- Inspection Procedure 3: The luggage compartment light does not illuminate normally
- Inspection Procedure 4: The foot light does not illuminate normally
- Inspection Procedure 5: The interior light auto-cut function does not operate correctly
- Inspection Procedure 1: The hazard warning lights do not illuminate
- Headlight Automatic Leveling Ecu Terminal Voltage
- Headlight
- Headlight Automatic Leveling System
- Fog Light
- Daytime Running Light
- Side Turn-Signal Light
- Dome Light
- High-Mounted Stoplight
- License Plate Light
- Hazard Warning Light
- ETACS
- General Information
- Special Tool
- Diagnosis
- Standard Flow Of Diagnostic Troubleshooting
- Diagnostic Function
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- DTC U0001: Bus off (CAN-C) ; DTC U0019: Bus off (CAN-B)
- DTC U0100: Engine control module CAN timeout
- DTC U0101: Transaxle control module CAN timeout
- DTC U0114: AWD-ECU CAN timeout
- DTC U0121: ABS-ECU or ASC-ECU CAN timeout
- DTC U0126: Steering wheel sensor CAN timeout
- DTC U0151: SRS-ECU CAN timeout
- DTC U0154: Occupant classification-ECU CAN timeout
- DTC U0155: Combination meter CAN timeout
- DTC U0164: A/C-ECU CAN timeout
- DTC U0168: WCM or KOS-ECU CAN timeout
- DTC U0184: Audio CAN timeout
- DTC U0195: Satellite radio tuner CAN timeout
- DTC U0197: Hands free module CAN timeout
- DTC U0245: Audio visual navigation unit CAN timeout
- DTC U1108: Excess CAN-B ECU Detection
- DTC U1120: Bus line (CAN-C) low input; DTC U1121: Bus line (CAN-C) high input
- DTC U0331: ECU internal error
- DTC B1761: Chassis number not recorded
- DTC B210A: +B power supply (low input); DTC B210B: +B power supply (high input)
- DTC B222C: Coding incomplete
- DTC B2206: Chassis number does not match
- DTC B2215: ECU internal error
- DTC B2353: Ignition power supply (low input); DTC B2354: Ignition power supply (high input)
- Data List Reference Table
- Trouble Symptom Chart
- Symptom Procedures
- Trouble Symptom Chart For Input Signal
- Input Signal Procedures
- Inspection Procedure 1: ETACS-ECU does not receive any signal from the ignition switch (ACC)
- Inspection Procedure 2: ETACS-ECU does not receive any signal from the ignition switch (IG1)
- Inspection Procedure 3: ETACS-ECU does not receive any signal from the key reminder switch
- Inspection Procedure 4: ETACS-ECU does not receive any signal from the front door lock actuator
- Inspection Procedure 5: ETACS-ECU does not receive any signal from the front door switch (LH)
- Inspection Procedure 6: ETACS-ECU does not receive any signal from the front door switch (RH)
- Inspection Procedure 7: ETACS-ECU does not receive any signal from the rear door switch (LH)
- Inspection Procedure 8: ETACS-ECU does not receive any signal from the rear door switch (RH)
- Inspection Procedure 9: ETACS-ECU does not receive any signal from the liftgate switch
- Inspection Procedure 10: ETACS-ECU does not receive any signal from the hood switch
- Inspection Procedure 11: ETACS-ECU does not receive any signal from the hazard warning light switch
- Inspection Procedure 12: ETACS-ECU does not receive any signal from the column switch signal
- On-Vehicle Service
- ETACS-Ecu
- Check With Terminal Voltage
- Accessory
- General Information
- Accessory Socket
- Ac Power Supply
- Hands-Free Cellular Phone System
- Diagnosis
- Symptom Procedures
- Inspection Procedure 1: Hands-free cellular phone system does not work normally
- Inspection Procedure 2: During the conversation with the hands-free system, the speaker's voice cannot be heard by the other party
- Inspection Procedure 3: During the conversation with the hands-free system, the voice of other party cannot be heard
- Inspection Procedure 4: Even when the steering voice-control switch is operated, the conversation is not possible
- Inspection Procedure 5: The cellular phone is not recognized or the connection cannot be established
- Inspection Procedure 6: Check the hands-free module power supply circuit
- Removal And Installation
- Steering Wheel Voice-Control Switch Continuity Check
- Alarm System
- General Information
- Special Tools
- Diagnosis
- Standard Flow Of Diagnostic Troubleshooting
- Diagnostic Function
- Trouble Symptom Chart
- Symptom Procedures
- Inspection Procedure 1: The theft-alarm is not armed (the theft-alarm indicator does not illuminate)
- Inspection Procedure 2: The interior alarm does not work normally while the theft-alarm is triggered
- Inspection Procedure 3: Theft-alarm horn does not sound while the theft-alarm system is triggered
- Inspection Procedure 4: Horns do not sound while the theft-alarm system is triggered
- Inspection Procedure 5: Panic alarm does not work normally
- On-Vehicle Service
- Horn
- Theft Alarm
- Panic Alarm System
- Ignition Switch
- Column Switch
- Defogger
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.