SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMITSUBISHI2007ENDEAVOR SE, FWDREPAIR AND DIAGNOSIS (SINGLE PAGE)ACCESSORIES & EQUIPMENTANTI-THEFT SYSTEMSCHASSIS ELECTRICALMULTI-CENTER DISPLAYON-VEHICLE SERVICESPECIAL TOOLS
2007 Mitsubishi Endeavor SE, FWD

Special Tools

2007 Mitsubishi Endeavor SE, FWDSECTION Special Tools
SPECIAL TOOLS

TOOL TOOL NUMBER AND NAME SUPERSESSION APPLICATION
A
G04289862G04289863G04289864G04289865G04289866G04289867G04289868

B
G04289862G04289863G04289864G04289865G04289866G04289867G04289868

C
G04289862G04289863G04289864G04289865G04289866G04289867G04289868

D
G04289862G04289863G04289864G04289865G04289866G04289867G04289868

E
G04289862G04289863G04289864G04289865G04289866G04289867G04289868

F
G04289862G04289863G04289864G04289865G04289866G04289867G04289868

G
G04289862G04289863G04289864G04289865G04289866G04289867G04289868
 MB991958
  1. MB991824
  2. MB991827
  3. MB991910
  4. MB991911
  5. MB991914
  6. MB991825
  7. MB991826

M.U.T.-III sub assembly
  1. Vehicle communication interface (V.C.I).
  2. M.U.T.-III USB cable
  3. M.U.T.-III main harness A (Vehicles with CAN communication system)
  4. M.U.T.-III main harness B (Vehicles without CAN communication system)
  5. M.U.T.-III main harness C (for DaimlerChrysler models only)
  6. M.U.T.-III adapter harness
  7. M.U.T.-III trigger harness
 MB991824-KIT
NOTE: G: MB991826 M.U.T.-III trigger harness is not necessary when pushing V.C.I. ENTER key.
 Reading diagnostic trouble code
CAUTION: M.U.T.-III main harness A (MB991910) should be used. M.U.T.-III main harness B and C should not be used for this vehicle.
A
G04289869G04289870G04289871G04289872

B
G04289869G04289870G04289871G04289872

C
G04289869G04289870G04289871G04289872

D
G04289869G04289870G04289871G04289872
 MB991223
  1. MB991219
  2. MB991220
  3. MB991221
  4. MB991222

Harness set
  1. Test harness
  2. LED harness
  3. LED harness adapter
  4. Probe
 General service tool (jumper) Making voltage and resistance measurements during troubleshooting
  1. Connect pin contact pressure inspection
  2. Power circuit inspection
  3. Power circuit inspection
  4. Commercial tester connection
G04289873
 MB992006
Extra fine probe		 - Continuity check and voltage measurement at harness wire or connector for loose, corroded or damaged terminals, or terminals pushed back in the connector.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.